Search:

Type: Posts; User: tony_A

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 39 minute(s) ago.

  1. Thread: New Monarch

    by tony_A
    Replies
    16
    Views
    3,154

    Oh, saw the title of the thread and thought you...

    Oh, saw the title of the thread and thought you had a new lathe
  2. Replies
    140
    Views
    14,182

    Its based on the actual cutting edge of the drill...

    Its based on the actual cutting edge of the drill bit. Stefan mentioned in his vid that he leaves the outside corner of the drill bit fractionally high to allow for the material that the grinder...
  3. Replies
    140
    Views
    14,182

    The other thing that I have noticed is that the...

    The other thing that I have noticed is that the work holding head on these little grinders is somewhat flexible. When I have the cutting edge sharp on both facets I will take a final gentle and fine...
  4. Replies
    140
    Views
    14,182

    I am very much a learner myself when it comes to...

    I am very much a learner myself when it comes to 4 facet sharpening on the D-bit grinder and have produced a couple of those wedge shaped facets. I have also sharpened a number of drills with good...
  5. Replies
    140
    Views
    14,182

    Stefan G has a video on four facet grinding using...

    Stefan G has a video on four facet grinding using a D-bit grinder

    https://www.youtube.com/watch?v=I5b6h1Vddes&ab_channel=StefanGotteswinter
  6. Replies
    22
    Views
    2,207

    Rob, I recently turned something like what your...

    Rob, I recently turned something like what your looking at , in my case a pivot pin for a fence on an old table saw. I used mild steel and I expect that is what the other similar pin on the machine...
  7. Replies
    32
    Views
    7,682

    I've had a bit of a play with freeCAD and found...

    I've had a bit of a play with freeCAD and found the tutorials by "Adventures in Creation" were OK. He's put out quite a few vids if you find him OK to listen to.
    ...
  8. Replies
    78
    Views
    9,249

    I bought a 12mm Llambrich chuck for an electric...

    I bought a 12mm Llambrich chuck for an electric drill. Drills had a tendency to spin in the chuck under load and the mechanism seised up after a relatively short time. My preference would be a Vertex.
  9. Replies
    78
    Views
    9,249

    I have a 336 from H&F with a QCTP (also H&F). I...

    I have a 336 from H&F with a QCTP (also H&F). I mostly use 12mm tool holders for OD turning, CCMT inserts, 06 size. I find this combination handles most of what this lathe is capable of. Have a...
  10. Replies
    5
    Views
    1,815

    Looks like you've got it all sorted.

    Looks like you've got it all sorted.
  11. Replies
    5
    Views
    1,815

    There's a general rule of thumb that says...

    There's a general rule of thumb that says multiply the rpm by the diameter of the wood (in inches) and the result should be in the range of 6000 to 9000. If the wood is out of balance will have to...
  12. Replies
    20
    Views
    3,972

    Yep, thats my style of camping.

    Yep, thats my style of camping.
  13. Replies
    17
    Views
    2,532

    Have a 40ish yr old Hitachi with similar problem,...

    Have a 40ish yr old Hitachi with similar problem, caused initially by a jammed nut. Have used a hammer and cold chisel for years. I use my boot against the body of the grinder and wheel at the same...
  14. Replies
    70
    Views
    36,276

    Looking good shed. Did you get much shrinkage in...

    Looking good shed. Did you get much shrinkage in the bearing housing as a result of the welding.
  15. Replies
    0
    Views
    1,444

    Hercus change gears and thread dial.

    For sale on Gumtree in Tassie. Same seller is selling the change gears.

    https://www.gumtree.com.au/s-ad/glenorchy/power-tools/lathe-parts-hercus-imperial-thread-dial/1275173011
  16. Thread: Project Binky

    by tony_A
    Replies
    49
    Views
    25,404

    And using simple tools. Heard him say that much...

    And using simple tools. Heard him say that much of his prep work, cutting crank cases and heads into pieces to graft other bits on, was done with a hacksaw and a file. Although he now has a milling...
  17. Thread: Project Binky

    by tony_A
    Replies
    49
    Views
    25,404

    One I found a little while back is Alan Millyard...

    One I found a little while back is Alan Millyard whose work is maybe sort of a Binky of motorbikes (without witty voiceovers).
    This one is of a 5 liter V twin that he mostly built himself (and in...
  18. Replies
    9
    Views
    2,306

    Im fairly certain that you are correct Karl. I...

    Im fairly certain that you are correct Karl. I have one but have milled it down to 16mm to fit my QCTP. When buying it I found the descriptions on the web site a little confusing.
  19. Replies
    10
    Views
    27,326

    Came from an plantation eucalypt, bluegum to be...

    Came from an plantation eucalypt, bluegum to be specific. It was from a short length off the base of one tree, no other tree in the block was like it. From the outside it looked like that butt...
  20. Replies
    10
    Views
    27,326

    Plane and simple. This is one I knocked up...

    Plane and simple.


    This is one I knocked up earlier in the year.
    389197
    389196
    389198
  21. Replies
    15
    Views
    14,155

    Nice work Halifax. What wall thickness did you...

    Nice work Halifax. What wall thickness did you use on the main beam? Would be interested to hear some feedback after you have done some heavy cuts. I would like to do something similar with my 336.
  22. Replies
    14
    Views
    4,612

    Depends on the the size tool that the tool post...

    Depends on the the size tool that the tool post can accommodate. Tool holders with a 12mm shank will generally use 06 inserts while 16mm holders take 09
  23. Replies
    14
    Views
    4,612

    Plenty of good info above for you to make your...

    Plenty of good info above for you to make your choice. I have an H&F 336 lathe (300mm by1000mm) and went with the ccmt inserts, 0.2 nose radius. Purchased a set of holders with inserts off ebay. The...
  24. This is one example, not sure if it is the best....

    This is one example, not sure if it is the best. Im guessing that it would be strong enough. 24V, 470 rpm variable speed 3.4 kg.cm torque, $70 inc postage...
  25. Thanks J&H, have seen carbide flat bar on ebay...

    Thanks J&H, have seen carbide flat bar on ebay including 20 *2 *200mm for $30. Claimed to be Chinese YG8 grade which is supposedly roughly equivalent to Sandvik H10. Ill order some and see how it...
  26. J&H would you mind measuring the Sandvik scraper...

    J&H would you mind measuring the Sandvik scraper insert please, length and thickness.
    If I can get my lathe to somewhere about the point where you have got yours to then I think I will be happy. I...
  27. Thanks Marcus. What length do you make the metal...

    Thanks Marcus. What length do you make the metal shank in the scrapers? If you happened to get down to Tassie at some point in the future would you be interested in running a course and if so what...
  28. Thanks again J&H, I haven't got any excuses not...

    Thanks again J&H, I haven't got any excuses not to give it a go. Wont happen this year though and
    if I had a reason to go to Brisbane I would be happy to pay for a day or two of tuition from Marcus.
  29. Thanks for the detailed reply J&H. My learning...

    Thanks for the detailed reply J&H. My learning process sounds similar to yours, reading on the internet and you tube. Encouraging to see that acceptable (to me) results can be obtained.
    Did you...
  30. Nice write up J&H, thanks for taking the time to...

    Nice write up J&H, thanks for taking the time to post it here. I have a 336 and pulled the compound and and cross slide off for a good clean when I got it. The ways on mine look about the same...
  31. Replies
    3
    Views
    3,757

    318 and 324 are weird numbers for a rotary table....

    318 and 324 are weird numbers for a rotary table. 360 would make a lot more sense.
  32. Replies
    14
    Views
    2,677

    If anyone ran something like that in Tassie I...

    If anyone ran something like that in Tassie I would be interested, Not an option for the foreseeable future though. A working week (40 hrs) at $30 per hour would be cheaper that a Richard King...
  33. I've an AL 336 and same problem. Trying to take...

    I've an AL 336 and same problem. Trying to take an exact depth cut has a bit of a guess factor in it, needless to say an accurate result isn't guaranteed. Was looking at setting up an 50mm dial...
  34. Replies
    154
    Views
    43,509

    Purchased a couple of items of aliexpress on the...

    Purchased a couple of items of aliexpress on the 16th June and two of the packages turned up yesterday, just over a month. Happy enough with that.
  35. Replies
    154
    Views
    43,509

    Cant complain about that, I've waited that long...

    Cant complain about that, I've waited that long for things to come from Brisbane.
  36. Replies
    22
    Views
    6,065

    I use an old sheet. Am mainly wanting to keep...

    I use an old sheet. Am mainly wanting to keep dust of the machines. Have notices on woodworking machines that horizontal surfaces rust much faster than vertical surfaces. I believe that dust on a...
  37. Replies
    9
    Views
    2,711

    Will go the end mill route and see how I get on. ...

    Will go the end mill route and see how I get on.
    Thanks for the offer Kryn but I can see myself wanting to counterbore for cap screws from time to time so will buy instead.
    Thanks for the...
  38. Replies
    9
    Views
    2,711

    Counterboring options

    Am wanting to counterbore M12 capscrews in 4140, a dozen holes. An M12 counterbore from Sutton is well over $200 so that's not an going to happen.
    What options do people use?
    Would a 20mm 2...
  39. Replies
    10
    Views
    2,903

    They would carry a bag of coal on the back seat...

    They would carry a bag of coal on the back seat if needed for the return trip. Getting that out of the car into the gas producer was also a dirty job.
  40. Replies
    10
    Views
    2,903

    That is pretty cool Bob. I have heard about these...

    That is pretty cool Bob. I have heard about these from my father but have not seen one set up for use. They were used during second world war when petrol was rationed and were gutless as all hell...
  41. I also have a 336d from H&F. I stripped the chuck...

    I also have a 336d from H&F. I stripped the chuck down, de-burred and washed it then repacked it with grease. There was a significant amount of grit in the chuck. What I did was based on one of...
  42. Replies
    154
    Views
    43,509

    Thanks John. keep us umm ... posted. I dont mind...

    Thanks John. keep us umm ... posted. I dont mind waiting for one or two months as long as the goods eventually arrive.

    Tony
  43. Replies
    11
    Views
    4,992

    That's an impressive example of improvisation Pete

    That's an impressive example of improvisation Pete
  44. Replies
    154
    Views
    43,509

    Thanks Dave A quick google search found this ...

    Thanks Dave
    A quick google search found this


    About half of the air cargo carried worldwide normally flies in the belly of passenger jets rather than in dedicated freighters. But deep flight...
  45. Replies
    154
    Views
    43,509

    Thanks for the replies, looks like its about to...

    Thanks for the replies, looks like its about to get a whole lot slower with what our gov is about to introduce. Might leave any purchase until things settle down.
  46. Replies
    154
    Views
    43,509

    Anyone bought from China lately

    Has anyone bought off Aliexpress recently and received their goods. As best as I can tell from a google search sea freight is starting to crank up again but what little air freight there is is taken...
  47. Replies
    2
    Views
    3,777

    To use google type in site:metalworkforums.com ...

    To use google type in
    site:metalworkforums.com
    then space followed by your search query. That restricts google to this site
    The following will search the forum for posts on 4140...
  48. Replies
    10
    Views
    3,696

    The JET GHB-1236 lathe is very similar. I have...

    The JET GHB-1236 lathe is very similar. I have found for other machines that JET have thorough manuals and they are based on the same generic Chinese machines that many of us have. I have downloaded...
  49. Replies
    23
    Views
    5,854

    Am in a similar situation, have been able to...

    Am in a similar situation, have been able to clamp the vice to the table with 4 regular hold down clamps but it looks messy. Picked up a couple of clamps similar to the ebay specials in #4 above but...
  50. Thread: Bush Fires !

    by tony_A
    Replies
    59
    Views
    20,464

    Fuel reduction burning certainly has an important...

    Fuel reduction burning certainly has an important role to play in helping to reduce the impact from wildfires, I've been involved with many fuel reduction burns both as a firefighter and in planning...
Results 1 to 50 of 73
Page 1 of 2 1 2