Search:
Type: Posts; User: Hugh Venables
Search: Search took 0.00 seconds.
-
28th Nov 2023, 08:51 AM
Thread: CVA Lathe
by Hugh Venables- Replies
- 6
- Views
- 5,695
Thanks Michael, I fear you are correct but...
Thanks Michael, I fear you are correct but nothing ventured, nothing gained. I have an acquaintance nearby I can borrow more info from. I only have the original operators manual. Yes, I would need...
-
27th Nov 2023, 03:14 PM
Thread: CVA Lathe
by Hugh Venables- Replies
- 6
- Views
- 5,695
CVA lathe discussion
If anyone would like to discuss CVA lathes I have one that was purchased new in 1966. I would like to add a taper turning attachment to it if I could find one. I would need the telescopic cross slide...
-
27th Nov 2023, 03:07 PM
- Replies
- 0
- Views
- 487
CVA lathe taper turning attachment wanted
I guess this is a bit of a long shot but if anyone can help me find a lonely taper turning attachment looking for a new home I would be most appreciative. I’m in Melbourne eastern suburbs.
-
30th Aug 2021, 09:57 PM
- Replies
- 6
- Views
- 2,494
Thanks Grahame for that clarification. When you...
Thanks Grahame for that clarification. When you put those two points together like that it is very clear.
Hugh -
30th Aug 2021, 05:44 PM
- Replies
- 6
- Views
- 2,494
Thanks Grahame, yes it all seems fine and I have...
Thanks Grahame, yes it all seems fine and I have successfully posted since.
I had a reply to my question asking for comments about a supplier. The replier was not prepared to comment on... -
30th Aug 2021, 01:09 PM
- Replies
- 15
- Views
- 4,818
Thanks racingtadpole. I will give them a go and...
Thanks racingtadpole. I will give them a go and hope I don’t have to negotiate later. I would hope that the forum rules would permit polite reporting of facts without opinion but I don’t read that...
-
29th Aug 2021, 07:53 PM
- Replies
- 6
- Views
- 2,494
Thanks Grahame. That empty title box looked so...
Thanks Grahame. That empty title box looked so inviting!
Hugh -
29th Aug 2021, 06:02 PM
- Replies
- 6
- Views
- 2,494
Unable to add post to thread; token has expired
I have written a long post to add to the M&G productions ER .........review. I pressed “submit” and assumed it had gone. Some time later I realised it was still sitting there waiting to be submitted...
-
29th Aug 2021, 12:48 PM
- Replies
- 15
- Views
- 4,818
What great thread. Thanks all. I can’t find an...
What great thread. Thanks all. I can’t find an available ER32 to D1-3 and I share the concern that I might buy one that didn’t run quite true anyway so I’m happy to cobble one together. I see that...
-
25th Aug 2021, 11:37 AM
Thread: G’day Guys
by Hugh Venables- Replies
- 10
- Views
- 2,688
Hi clear out/H, I hear what you are saying about...
Hi clear out/H,
I hear what you are saying about the great OHS fiasco almost all of which is just an enormous cost to industry and a waste of time and effort. The last raid we had by Worksafe... -
24th Aug 2021, 11:42 PM
Thread: G’day Guys
by Hugh Venables- Replies
- 10
- Views
- 2,688
Thanks Grahame, it looks like I wasn’t looking...
Thanks Grahame, it looks like I wasn’t looking for SETTINGS at all. My email is fine but the message is still there. I’ll just ignore it.
Hugh -
24th Aug 2021, 10:23 PM
Thread: G’day Guys
by Hugh Venables- Replies
- 10
- Views
- 2,688
Thanks Grahame. I have a message from Neil asking...
Thanks Grahame. I have a message from Neil asking me to go to SETTINGS to make sure my email address is up to date. I haven’t been able to find SETTINGS.
Hugh -
24th Aug 2021, 10:08 PM
Thread: G’day Guys
by Hugh Venables- Replies
- 10
- Views
- 2,688
On this CVA there is a rotation detector on the...
On this CVA there is a rotation detector on the motor shaft that, on rotation, closes a set of contacts that are in series with the normally closed contacts in the contractor that is switching the...
-
24th Aug 2021, 07:12 PM
Thread: G’day Guys
by Hugh Venables- Replies
- 10
- Views
- 2,688
G’day Guys
I’m going to use my actual name as my username which is Hugh Venables. I live in Ferntree Gully Vic with my wife Di and my garage. I grew up in Eltham and completed HSC at Eltham High. I was...