Search:

Type: Posts; User: Dero

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    4,331

    I purchased some more tool holders from PeeWee...

    I purchased some more tool holders from PeeWee about 6 months ago , once I translated the website , I found them good to deal with & quality is good as far as my limited experience can tell .
  2. Replies
    49
    Views
    3,748

    The reason being that the OD fits all fittings ,...

    The reason being that the OD fits all fittings , threaded , welded etc . If the OD changed then a thick wall pipe would not fit a std fitting .
  3. Replies
    13
    Views
    1,012

    The last time I saw this it turned out to be just...

    The last time I saw this it turned out to be just a slipping belt .
  4. Thread: Parting blade

    by Dero
    Replies
    2
    Views
    741

    Thanks Grahame , I bit the bullet a ordered the...

    Thanks Grahame ,
    I bit the bullet a ordered the tool & blades from EE .
  5. Thread: Parting blade

    by Dero
    Replies
    2
    Views
    741

    Parting blade

    I currently have a flat blade , no taper , Hss parting blade ...3mm x 25mm . I would like to try a T type blade . Do I need a different holder to take the T type blade ? My current blade has a taper...
  6. Thread: Mill Drill WA

    by Dero
    Replies
    4
    Views
    1,130

    Sold

    Sold
  7. Thread: Mill Drill WA

    by Dero
    Replies
    4
    Views
    1,130

    Yes , that"s the one

    Yes , that"s the one
  8. Thread: Mill Drill WA

    by Dero
    Replies
    4
    Views
    1,130

    Mill Drill WA

    I am selling my mill drill on gumtree & facebook market place .
    Located in Boyup Brook.
    It is in very good condition & comes with some basic tooling .
    Worth a look if you are interested .
  9. Thread: New Mill

    by Dero
    Replies
    6
    Views
    1,761

    Thanks to Simon for his very helpful PM's with...

    Thanks to Simon for his very helpful PM's with pictures ,of the pacific mill.
    Much appreciated .
  10. Thread: New Mill

    by Dero
    Replies
    6
    Views
    1,761

    New Mill

    Looking for owners of either a Pacific FT2 or a First 1 1/2 mills .
    I am thinking of getting a 2nd hand Pacific or a new First mill & trying to justify the expense of the new one .
    All feedback on...
  11. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    Got it . Thanks to all .

    Got it .
    Thanks to all .
  12. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    I still have no idea what the taper is for , or...

    I still have no idea what the taper is for , or the 2 hex head screws . Maybe together they hold & support the geared drive setup ?
  13. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    398627 I cant seem to rotate pic with what I have...

    398627 I cant seem to rotate pic with what I have . This is the rear taper .
  14. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    OK next question . If using a collet chuck in...

    OK next question .
    If using a collet chuck in the MT4 taper , would you just rely on the taper or use some kind of draw bar to hold it in ?
  15. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    It has an input shaft on the back as well , this...

    It has an input shaft on the back as well , this is the rear of the hollow spindle .
    Sorry , not good with photos , I'm a bit of a dinosaur , and woefully bad internet here .
  16. Thread: Dividing Head

    by Dero
    Replies
    14
    Views
    1,708

    Dividing Head

    I have just cleaned up a universal dividing head [ I have never used one ] the front of the spindle has an MT4 taper but the taper in the rear is neither MT3 or 4 , what is it for ?
  17. Replies
    15
    Views
    1,462

    Thinking about it a bit more , my previous post...

    Thinking about it a bit more , my previous post re 1000C , I may be wrong .
  18. Replies
    15
    Views
    1,462

    I have a 1000C , been a while since I did it but...

    I have a 1000C , been a while since I did it but all I need to do is put the correct gear in and cut as per normal with the dial .
  19. Replies
    11
    Views
    1,413

    A while back I was looking for a safe , a very...

    A while back I was looking for a safe , a very heavy one came up in the east , I'm in WA , after a lot of ringing around , the freight ranged from $1200 to $100 .
    I had to wait for their convenience...
  20. Replies
    22
    Views
    4,331

    I had the exact same problem with create a few...

    I had the exact same problem with create a few months ago .
    I ordered from Pee Wee & am quite happy with the tool holders I received .
  21. Thread: small mill

    by Dero
    Replies
    18
    Views
    2,825

    Both the ones I am looking at have power feed on...

    Both the ones I am looking at have power feed on the X axis , but I can only go on the sales pitch for rigidity .
    Being in the west , I can't find any on the shop floor other than hare & forbes .
  22. Thread: small mill

    by Dero
    Replies
    18
    Views
    2,825

    Not having owned a mill before I have no real...

    Not having owned a mill before I have no real plan for it , other than small parts .
    S/S is a must for motorcycle parts etc , other than that I will see where it takes me .
    I used a mill with an...
  23. Thread: small mill

    by Dero
    Replies
    18
    Views
    2,825

    The plan for the SX4 was to bench mount it , so...

    The plan for the SX4 was to bench mount it , so if I lash out on the knee mill , I can fit a drill on the bench .
    A lot more money though .
  24. Thread: small mill

    by Dero
    Replies
    18
    Views
    2,825

    One other thing . I have a floor mount pedestal...

    One other thing .
    I have a floor mount pedestal drill , would the mill make it obsolete or will I still need it ?
    The reason I ask is that if the drill goes it would be much easier to fit the knee...
  25. Thread: small mill

    by Dero
    Replies
    18
    Views
    2,825

    small mill

    Hi all , I am new to the forum , nice to find an Aussie forum , looking forward to it .

    I am looking at a new mill , my first one , I was thinking of the Sieg SX4 , but I am tempted to lash out...
Results 1 to 25 of 25