Search:

Type: Posts; User: Ulfr

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,494

    Thank you, that does look good! I might have to...

    Thank you, that does look good! I might have to remove the internal lip though and hold it in place with the screws through the sheet (panel form shed). Mine might extend slightly too far past the...
  2. Replies
    2
    Views
    1,494

    Mice proofing trim deck

    Hi All

    is there a best way to mouse proof trimdek cladding around the base of a workshop slab? As in the holes left by the profile around the outside of the slab.

    I finished my workshop...
  3. Replies
    9
    Views
    6,215

    Thank you all for the help and interesting...

    Thank you all for the help and interesting discussion. I actually saw another orange offset like Chas’ in my (internet) search, but had seen a bunch of colours across the different vices including...
  4. Replies
    9
    Views
    6,215

    Joplin vice colour

    Hi All

    anyone know the original colour of Joplin vices? Going to give this little vice a freshen up, not sure if the green is the colour and couldn’t find that info.

    Thanks all.
  5. Replies
    10
    Views
    7,164

    no worries :) Haha didn’t mean to *pictures?*...

    no worries :)

    Haha didn’t mean to *pictures?* your post but have no idea how to undo that.

    glad they worked, hopefully they can be saved somewhere semi permenant.
  6. Replies
    10
    Views
    7,164

    See if this works:

    See if this works:
  7. Replies
    10
    Views
    7,164

    I have scanned these in colour. They look great...

    I have scanned these in colour. They look great but I cannot upload them as the limit is 5MB (These are 8 and a bit over 5 MB respectively). Is there a way to do it?
  8. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Actually does anybody have a photo of the later...

    Actually does anybody have a photo of the later model dowels? I did find two of these which fit the dowel holes and and have the smaller threaded end which seems to match the recessed thread in the...
  9. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Many many thanks to Mal, I have a vertical head...

    Many many thanks to Mal, I have a vertical head and tail stock for the dividing head :)


    Will do the arbor/spiggot and dowels.
  10. Replies
    10
    Views
    7,164

    Sounds like a plan, will scan them this week...

    Sounds like a plan, will scan them this week hopefully.
  11. Replies
    10
    Views
    7,164

    I can scan these if the other ones are different?...

    I can scan these if the other ones are different? I can’t see them.
  12. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Good question Terry. I see 3 holes either side of...

    Good question Terry. I see 3 holes either side of my spindle so I suspect that is the four bolts (I think later are four) and two dowels but don’t know for sure.

    Took the vice off For the first...
  13. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Thanks so much Bob. i have a longer one here...

    Thanks so much Bob.

    i have a longer one here too, I didn’t even consider could be for the mill (assumed lathe).

    it has a wheel handle.
    388011
  14. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Will do Bob! And may take you up on that Eric. At...

    Will do Bob! And may take you up on that Eric. At the moment I'm waiting on some possible/promising parts so see what happens there :)



    In this photo, is this a drawbar and taper part (sorry I...
  15. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Thanks Bob! Looks like it doesn't it. After...

    Thanks Bob! Looks like it doesn't it. After seeing those pics I went to the box of bits that came with it and found one of the screws. Missing one but at least I know exactly what to replace them...
  16. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Moved the mill out of storage and into the garage...

    Moved the mill out of storage and into the garage until the workshop is complete. Going to start tidying it up. Goal is eventually to give it a full clean and respray but might start with the vice...
  17. Vertical head and tail stock Hercus model “O” wanted

    Hi all

    As per the title I’m looking for a vertical head and the tail stock for a Hercus model “O” mill. Let me know if you have one you don’t want or if you know where one might be.

    thank you
    ...
  18. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Thank you so much Terry for the pic and thank you...

    Thank you so much Terry for the pic and thank you NHO for those instructions.

    The mill is wrapped up in storage until I get the workshop finished but I took some pictures of what I had assumed was...
  19. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Tommy thank you for the reply. Not sure if all...

    Tommy thank you for the reply. Not sure if all that is among the pile of stuff that came with it, I'll look at pics and try to find it. Alot is hercus lathe stuff that may help someone here once I...
  20. Thread: Hercus model "O"

    by Ulfr
    Replies
    29
    Views
    14,736

    Hercus model "O"

    Hi

    I have been reading a lot of threads here as a guest but eventually had something to post. I'll start by saying I have limited experience, go easy on me :D

    For a while I have been wanting...
Results 1 to 20 of 21