Search:
Type: Posts; User: Mattgoodwin
Search: Search took 0.00 seconds.
-
8th Jul 2020, 12:17 PM
- Replies
- 16
- Views
- 8,927
Collets have now been sold. Faceplate is still...
Collets have now been sold.
Faceplate is still available -
22nd May 2020, 05:41 PM
- Replies
- 16
- Views
- 8,927
No worries Ian, the info may help someone in the...
No worries Ian, the info may help someone in the future.
I don't mind if you want to throw an offer at me. I honestly don't know what they are worth, and I guess they are only worth what someone... -
22nd May 2020, 02:03 PM
- Replies
- 16
- Views
- 8,927
Hi Ian, No problem at all. I would rather you be...
Hi Ian,
No problem at all. I would rather you be sure!
I have attached some photos with measurements of the collets and holder. The thread on the collets is 26tpi
The internal taper for the... -
22nd May 2020, 11:18 AM
- Replies
- 16
- Views
- 8,927
Hi Ian and Tom I have a attached a photo of...
Hi Ian and Tom
I have a attached a photo of all the measurements of the bar, hopefully this helps!
As for collet sizes, I went through and used some imperial drill bit shanks to work out what... -
20th May 2020, 08:51 AM
- Replies
- 16
- Views
- 8,927
Hi Ian Sorry I can't be of more help with...
Hi Ian
Sorry I can't be of more help with this. I have never used a collet setup myself, this was stuff that came with a lathe that I no longer have.
Where are you located?
Matt -
13th May 2020, 12:48 PM
- Replies
- 16
- Views
- 8,927
386522 Hi Ian I have measured the length...
386522
Hi Ian
I have measured the length of the drawbar at 266mm from the threaded female end to the shoulder. Its diameter is 19mm or 3/4 inch.
I'd also be happy to swap or part exchange... -
11th May 2020, 01:24 PM
- Replies
- 16
- Views
- 8,927
Hercus Lathe Collet set and Face plate.
Came with a Hercus 9c
Hercus collet set - $350
15 Collets and Draw bar.
Weight 2.2 Kgs
Face Plate - $50
(I measured the hole at 1 3/8 x 8tpi)
Weight 3.5kgs -
20th Apr 2020, 02:26 PM
Thread: Help Identifying Dividing head.
by Mattgoodwin- Replies
- 10
- Views
- 2,411
I have gotten some info on the lathe this was...
I have gotten some info on the lathe this was attached to - The lathe and dividing head arent mine, they are my uncles who I am communicating for. I'm working on getting him onto this site himself. ...
-
16th Apr 2020, 01:51 PM
Thread: Help Identifying Dividing head.
by Mattgoodwin- Replies
- 10
- Views
- 2,411
Thankyou for the warm welcome to the forum! I...
Thankyou for the warm welcome to the forum!
I have already gathered so much useful information!
I'm fairly new to machining and using Mills and lathes so there will no doubt be some more... -
14th Apr 2020, 02:17 PM
Thread: Help Identifying Dividing head.
by Mattgoodwin- Replies
- 10
- Views
- 2,411
Help Identifying Dividing head.
Hi there,
I'm wondering if anybody can help me identify this dividing head, and what use it possibly serves?
It came with an old lathe. Its fairly small, so I was thinking it may be useful for...