Search:

Type: Posts; User: Ando81

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    1,973

    Depending on the size of your work piece but...

    Depending on the size of your work piece but could you hold it in a pedestal drill to turn it and use a cutting edge to cut the groove? I’m just trying to think outside of the box [emoji2369] I’m...
  2. Replies
    23
    Views
    4,239

    That’s great Pete [emoji1303] I’m glad it’s...

    That’s great Pete [emoji1303] I’m glad it’s working well for you, well done [emoji1305]
  3. Replies
    23
    Views
    4,239

    Yes, the point I was trying to make was that you...

    Yes, the point I was trying to make was that you shouldn’t assume that the pto would be revving at 540 at idle and improve from there. Most power packs are fine to operate at lower revs but may just...
  4. Replies
    23
    Views
    4,239

    I’m not trying to be rude mate but most tractors...

    I’m not trying to be rude mate but most tractors I’ve operated have a pto speed of 540 when the tractor is revving close to 1800rpm. Yours may be different but Just something to be aware of...
  5. Replies
    154
    Views
    43,482

    I ordered some chainsaw accessories from China on...

    I ordered some chainsaw accessories from China on Feb 5 to be delivered with tracking. All was going well until Feb 8 then it ended up with China Post. There’s been no tracking available since and...
  6. Pm sent.

    Pm sent.
  7. I’m stuck in Victoria too otherwise I’d take the...

    I’m stuck in Victoria too otherwise I’d take the mig welder [emoji30]
  8. I’m not sure of anyone personally but there’s a...

    I’m not sure of anyone personally but there’s a few engineering businesses in Shepparton or Bendigo that probably have one. Or are you trying to do a “mates rates” type of deal? No judgement if you...
  9. Replies
    10
    Views
    4,083

    I would go with the new axles and save all...

    I would go with the new axles and save all potential headaches. I’d be heartbroken to see any damage done to your trailer for the sake of trying to save time and a couple of hundred dollars. Also by...
  10. I did however find some $10 flared spanner sets...

    I did however find some $10 flared spanner sets in some stores not too far from me.
  11. It’s funny that you mentioned stock not being...

    It’s funny that you mentioned stock not being available. For interest sake, I searched a lot of stores from Victoria to Queensland and even Wa with no stock of the safe case. I often wonder if these...
  12. Replies
    30
    Views
    5,498

    Cordless power tools..

    I have all Aeg tools and for my diy jobs it’s great. The brushless oil pulse impact driver is an animal with lots of grunt. I compared it to a standard Aeg impact driver in my local Bunnings drilling...
  13. Replies
    5
    Views
    2,913

    No worries, I’ll keep an eye out for a suitable...

    No worries, I’ll keep an eye out for a suitable motor in my area.
  14. Replies
    5
    Views
    2,913

    Ok, I’m interested but probably wouldn’t be able...

    Ok, I’m interested but probably wouldn’t be able to get to have a look at till mid to late next week. I’ll stay in touch and try to organise a time to drop down to see it.
  15. Replies
    5
    Views
    2,913

    This sounds like an interesting project, are you...

    This sounds like an interesting project, are you saying that you may have a motor to suit? If not, could you recommend a suitable motor rpm speed so that I could try to source one if I did happen to...
  16. Replies
    3
    Views
    4,198

    Hi, I really enjoy Torquay. It’s a beautiful...

    Hi, I really enjoy Torquay. It’s a beautiful place to visit for a holiday. You are very fortunate to live in a great part of Victoria [emoji1303]
  17. Replies
    9
    Views
    8,078

    What town are you in mate?

    What town are you in mate?
  18. Thread: Copper Tube

    by Ando81
    Replies
    13
    Views
    8,444

    A scrap dealer would be a good idea I think. A...

    A scrap dealer would be a good idea I think. A sprinkler fitter would use plenty of larger diameter pipe also. It might be worth a phone call to a fire services business to ask them if you could buy...
  19. Replies
    9
    Views
    8,078

    Thanks for the warm welcome Grahame. I’ve found...

    Thanks for the warm welcome Grahame. I’ve found on car based forums that if everyone respects each other than they are a great place to share knowledge. I’ll probably take a while to find my feet,...
  20. Replies
    22
    Views
    11,541

    Boc argon cylinder for sale beware FB

    I bought a Speedgas argon mix a while ago and I’m much happier to have it than BOC with their rental charges. It’s a D size as I only do diy repairs and don’t use a lot of gas. I would happily...
  21. Replies
    9
    Views
    8,078

    I’m accustomed to that on forums Ken but thanks...

    I’m accustomed to that on forums Ken but thanks for the heads up anyway. Nagambie isn’t too far away from Kyabram, 45 mins to an hour isn’t it?
  22. Replies
    9
    Views
    8,078

    Hi, New member Shepparton area.

    Hi all, I’m interested in all things metal work but am in no way qualified. I can do basic farm repairs with a MIG welder and can do very limited TIG welding and average ARC welding. Just thought I’d...
Results 1 to 22 of 22