Results 166 to 180 of 941
Thread: What did you learn today?
-
8th May 2013, 03:03 PM #166Most Valued Member
- Join Date
- Jun 2011
- Location
- Australia east coast
- Age
- 71
- Posts
- 2,713
-
30th Jun 2013, 11:43 PM #167Distracted Member
- Join Date
- May 2010
- Location
- Lower Lakes SA
- Age
- 58
- Posts
- 2,607
Dial bore gauges read backwards. (I just bought some and hadn't used them before.) So I made a bush OD 44.48 instead of 44.52.
I might get away with loctite, but I think I will make the part again for penance.
-
1st Jul 2013, 04:35 PM #168Intermediate Member
- Join Date
- May 2013
- Location
- QLD
- Posts
- 47
I have recently found out that changing welding sticks bear foot with the ground attached to a poll going into a ditch is a bad idea, 48volt through the system later and to this day I will not change a welding stick.
I tried to be good.
But the other options where better.
-
1st Jul 2013, 08:20 PM #169
ouch.
Can relate to that sensation.... the old farm welder has had a handpiece upgrade as there used to be a screw that would come loose just enough to touch my wrist. Holding the grounded job with the other hand lead to some expressions of surprise.
The new handpiece was a great investment.Last edited by HavinaGo; 2nd Jul 2013 at 02:24 AM. Reason: headpiece is now handpiece ... auto correct mumble mumble bah humbug
cheers
David
------------------------------------------------
A society grows great when old men plant trees whose shade they’ll never sit in. (Greek proverb)
-
2nd Jul 2013, 01:04 AM #170Senior Member
- Join Date
- Apr 2008
- Location
- Perth
- Posts
- 269
What I learnt today
French drivers tail gate, don't obey any posted speed limit, do not pull over to allow emergency vehicles to pass and don't indicate when passing.
The food is tops though.
DD
-
2nd Jul 2013, 01:52 AM #171
I learned today that the letter "M" as in M16x2 doesn't stand for metric.... you live and learn... I leave it as an exercise for those with a copy of machinery's handbook to discover more...
Regards
Ray
-
2nd Jul 2013, 02:32 AM #172cheers
David
------------------------------------------------
A society grows great when old men plant trees whose shade they’ll never sit in. (Greek proverb)
-
2nd Jul 2013, 09:06 AM #173
-
2nd Jul 2013, 10:49 AM #174
I was told some years ago that pepper makes a good first aid tool, and it stops bleeding. I never really believed it, but, yesterday I learnt that it is true, I cut my hand in a spot where a bandaid wouldn't work. I was bleeding like mad, no amount of paper towel seemed to stop it. I spotted the pepper shaker on the shelf and in desperation ground some on the cut.......bleeding stopped almost instantly. Handy thing to know I think!
As for welding, I was helping weld some frames up years ago. My boss was cursing at the welder cause he couldn't strike an arc. Of course he tried before I had the clamp on, here was me with the clamp in one hand and holding the frame in the other.....
Cheers,
Ew1915 17"x50" LeBlond heavy duty Lathe, 24" Queen city shaper, 1970's G Vernier FV.3.TO Universal Mill, 1958 Blohm HFS 6 surface grinder, 1942 Rivett 715 Lathe, 14"x40" Antrac Lathe, Startrite H225 Bandsaw, 1949 Hercus Camelback Drill press, 1947 Holbrook C10 Lathe.
-
2nd Jul 2013, 11:15 PM #175
-
6th Jul 2013, 11:01 PM #176
-
7th Jul 2013, 07:18 AM #177
-
7th Jul 2013, 09:28 PM #178
Metric profile,whats that then? Does in refer to the different thread angle profile from Imperial measured bolts or is this something else?
Well that is certainly confusing, and while I am not intending to start an argument, the statement is seemingly different to what Fastenal, the bolt manufacturing company say in print.
A cut and paste from their site follows --
"Metric Thread
The metric screw thread is identified by the capital letter M, followed by the nominal diameter. Metric
threads are measured by the distance between two adjacent threads in millimeters (pitch).
Threads on a standard (inch based) fastener are measured by counting the number of threads per inch."
Apart from that, lots of other good metric bolt specification info is there also.
http://www.fastenal.com/content/feds...ifications.pdf
I for one am happy to stick with Fastenal's system -as they say- It works for me.
Grahame
-
8th Jul 2013, 12:43 PM #179
Nothing wrong with Fastenal's description... and it's not incompatible with the description given in Machinery's Handbook.. it's just called the M profile, and there's an ISO standard if you google for "M thread profile" you should find it. There are lots of other metric profiles, MJ, S, etc..
Regards
Ray
-
8th Jul 2013, 02:46 PM #180
yesterday I learned to duck, when the chuck let go of the piece of wood I was turning. Pity I wasn't quick enough. No damage done (it hit me in the head, what damage could it do ). Always a problem when turning timber that's a little "punky"
I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys