Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
15th Jan 2020, 03:31 PM #1
Belt grinder tracking wheel question
The tracking wheel on my almost complete belt grinder is an ebay ali one, and it seems to have a very high crown, which I think is causing it to be very (too) sensitive.
A tiny bit of movement has the belt darting across the wheels, so I was wondering if reducing the height of the crown, and widening it somewhat, might reduce the sensitivity?
Cheers.
Grinder tracking wheel 1.jpg
-
15th Jan 2020, 03:43 PM #2Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,183
That does look high. It might be worth trying a few wraps of electrical tape around the outside of the wheel and say one wrap in the area between the outside and middle of the crown.
-
15th Jan 2020, 04:37 PM #3
-
15th Jan 2020, 06:29 PM #4Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,183
-
15th Jan 2020, 07:51 PM #5Most Valued Member
- Join Date
- Jul 2006
- Location
- Athelstone, SA 5076
- Posts
- 4,255
I bought my wheels from kmg. That looks to be about the same. I did take a lot of time ensuring that all wheels are centerally aligned radially.
My adjustment is 1/2 unc thread.
Also is the angular adjustment for the tracking wheel too long from pivot point?
-
15th Jan 2020, 08:42 PM #6
How wide is the wheel relative to the belt you are running? A narrow belt on a wide high crown wheel is much more sensitive than a wider belt on the same wheel and initial placement is more critical. Also how much tension are you running? Sometimes helps to back off the tension a little initially while you tune everything, as this can help desensitise the tracking, then slowing increase the tension to what you want to run at once you have beaten the tracking demon. Above comments apply to long belt grinders, not sure about how applicable the might be to knife style belt grinders, as the additional wheels/rollers in the system would influence everything as well, and a misaligned roller might have more effect than the tracking adjust can cope with.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
16th Jan 2020, 01:24 AM #7
-
16th Jan 2020, 01:37 AM #8
Thanks to Bobs suggestion, which resulted in the need of fresh underwear when the electrical tape let go at 5000+ RPM, I have it sorted.
The tracking wheel now has a barely descernable crown and is much less sensitive, but still very effective. The V shape has been remodeled into a very smooth gentle curve from one side to the other.
F.Y.I. the tracking wheel is 65mm wide, the drive wheel is 55mm wide and 200mm diam, and the belt is 1220 x 50. There are only the two wheels on this grinder. It is attached to an Abbott and Ashby 8" bench grinder.
Thanks for the assistance, much appreciated )
Similar Threads
-
Belt grinder wheel bore size
By ToolmanTim in forum METALWORK GENERALReplies: 7Last Post: 9th Jun 2019, 11:20 PM -
Macson surface grinder wheel removal question.
By lamestllama in forum METALWORK GENERALReplies: 13Last Post: 1st Jan 2019, 11:40 PM -
Twin belt belt grinder.
By onanonanon in forum METALWORK GENERALReplies: 6Last Post: 18th May 2018, 03:52 PM -
Multitool repairs to belt tracking cam
By Grahame Collins in forum METALWORK GENERALReplies: 2Last Post: 22nd May 2017, 07:50 PM -
hand wheel question
By texx in forum METALWORK GENERALReplies: 7Last Post: 1st Nov 2011, 08:06 AM