Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Pitts Lathe Circa 1890
-
28th Aug 2013, 02:35 PM #1Chief Swarf Maker
- Join Date
- Aug 2013
- Location
- Melbourne
- Posts
- 132
Pitts Lathe Circa 1890
Hi, thought you guys might get a kick out of this lathe i bought last year.
The story ends (for me) not long after, I cleaned it up into a usable state and made a small amount of swarf with it, then circumstances changed and i needed the space for a more precision/production oriented machine, and had to sell.
In the meantime i felt privileged to work on the kind of machinery my grandfather used as an apprentice. (i'm only a youngun)
All the features of these flash fangled modern lathes are there, albeit crudely. The 240v drive was clearly added on later as these were originally driven by shafts running through the entire factory. OHS inspector's nightmare!
Anywho, some pics. There is also some info on these gems over at Pitt's lathe
-
28th Aug 2013, 02:48 PM #2Chief Swarf Maker
- Join Date
- Aug 2013
- Location
- Melbourne
- Posts
- 132
Some of the bits and bobs I made up to get the machine useable and semi accurate
New cross slide bush, leadscrew and nut
Bushed at the other end and lash set via nylock nut
New compound slide screw, nut and bush. Lash is adjusted at this end via the 2 small c/sunk screws. LH thread so the handles worked as normal (originally RH)
Other end...
Annnndddd this is why i felt the need to turn up new leadscrews, apparently 120 odd years of use will produce "slight" wear
Toolpost bushed to maintain alignment
And faced where the compound slide swivels, had been broken and welded previously
That's about it! Never got a chance to paint it, but did scrape a LOT of gunk off it, and some sort of honeycomb type insect nest from under the apron.
-
28th Aug 2013, 06:12 PM #3Most Valued Member
- Join Date
- Jun 2012
- Location
- SA
- Posts
- 1,649
Nice old lathe. Pity you had to sell it.
Given how far you had gone with it, would have been worth finishing.
Great photos and thanks for posting.
Tony in the UK who runs Lathes.co.uk would almost certainly be interested in copies for his web blog. Ping him an email.
Cheers
Rob
-
28th Aug 2013, 08:11 PM #4Chief Swarf Maker
- Join Date
- Aug 2013
- Location
- Melbourne
- Posts
- 132
I think I sent him some photos, but i might have forgotten. I probably did forget, i'm good at doing that.
For me, the leather belt drive killed this thing in terms of any real usability, and space in my workshop is almost as valuable as spare time, so it had to go.
Aside from struggling to get enough power to the spindle, it worked quite well as a lathe and left a reasonable finish. It did scare the willies out of me with all the exposed gears etc though.
The guy who bought it was stoked, i dont blame him as there were a LOT of hours involved to bring it upto that condition. If he got the drive sorted it would be a great bit of gear for occasional use.
-
29th Aug 2013, 12:41 AM #5Most Valued Member
- Join Date
- May 2011
- Location
- Murray Bridge S Aust.
- Age
- 71
- Posts
- 5,959
I think the previous owners lost the "guards" off it all , great find though. As you say it's a pity to have to get rid of it, but room is room.
Kryn
Similar Threads
-
Whitworth Planer Circa 1850
By Anorak Bob in forum METALWORK GENERALReplies: 9Last Post: 8th Nov 2011, 06:23 PM