Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 7 of 7

Thread: Titanium

  1. #1
    Join Date
    Oct 2015
    Location
    melbourne
    Posts
    473

    Default Titanium

    G'day forumites..

    I have some sheet titanium with which I thought I'd try making a pendant. Any tips? I found I can cut it ok with a hacksaw, and a reasonable polish starting with a cheap diamond stone to 600 grit then some 600 wet and dry followed by Tripoli on a buff. Still some scratche though and a few pits on the back.
    I also tried heat colour with a little gas burner. Certainly got colour but very subtle. Would ox-acetylene be better? Does anodising give brighter colour?

  2. #2
    Join Date
    Feb 2012
    Location
    Tamworth, NSW
    Posts
    202

    Default

    Do you have any idea what grade of Ti you have? I’ve only used 6AL4v (grade 5) but with this heat colours are quite bright and it anodises very well. There are quite a few online tutorials with anodising - you will want a decent DC power source up to around 120v for all colours. The colours tend to repeat but you tend to get better lasting colour using the higher voltages. I guess because the surface oxide layer you form is thicker.

    for multiple colours anodising is fun. If you lay down the highest voltage colour first (mask off the other areas with nail polish or remove some colour via sand blasting etc) you can then continue to add other colours without changing your high voltage colour.

  3. #3
    Join Date
    Oct 2015
    Location
    melbourne
    Posts
    473

    Default

    Absolutely no idea... An auction find, along with a sheet of brass and copper..

    Have to dig through the junk box(es) for the makings of a variable supply..

  4. #4
    Join Date
    Aug 2008
    Location
    Melbourne
    Age
    34
    Posts
    1,075

    Default

    Ti-6-4 is the most commonly used titanium alloy by far, so chances are it's either that or pure titanium

  5. #5
    Join Date
    Nov 2007
    Location
    melbourne australia
    Posts
    3,228

    Default

    The anodising process is so quick, you can just use 9V batteries connected in series to get the desired voltage (it's almost instant). Of course that only gives you 9V increments. I suppose you could also place a variable power supply in series with the batteries to fine tune the voltage.
    Attached Images Attached Images
    Chris

  6. #6
    Join Date
    Oct 2020
    Location
    Greendale Vic. Australia
    Posts
    64

    Default Titanium colour

    I've used titanium inlays for guitars, and my Brit' bro' has used it a lot in his jewellery.
    I found that it polished beautifully, taking it to 1200 before putting it on the wheel.

    I used Mapp gas - got beautiful rainbow colour, but (with my titanium anyway) I had to seal it pretty soon after to hold the colour, otherwise it just goes dull and grey.
    (I used 2K Clear auto finish, It's held it's colour still, after at least 12 years).

  7. #7
    Join Date
    Nov 2007
    Location
    melbourne australia
    Posts
    3,228

    Default

    Quote Originally Posted by joolstacho View Post
    I used Mapp gas - got beautiful rainbow colour, but (with my titanium anyway) I had to seal it pretty soon after to hold the colour, otherwise it just goes dull and grey.
    That's odd. It shouldn't lose its colour unless it's subject to wear.
    Chris

Similar Threads

  1. Finishing titanium?
    By jhovel in forum METALWORK GENERAL
    Replies: 27
    Last Post: 23rd Nov 2020, 10:18 PM
  2. Titanium First Impressions
    By jack620 in forum METALWORK GENERAL
    Replies: 12
    Last Post: 23rd Sep 2018, 11:27 PM
  3. 3D printed Titanium Horseshoes
    By BobL in forum METALWORK GENERAL
    Replies: 16
    Last Post: 19th Oct 2013, 01:38 PM
  4. Milling Titanium
    By glock40sw in forum METALWORK GENERAL
    Replies: 1
    Last Post: 30th Aug 2007, 07:42 PM
  5. Titanium
    By Chris Parks in forum METALWORK GENERAL
    Replies: 8
    Last Post: 7th Jan 2007, 10:39 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •