Results 1 to 14 of 14
  1. #1
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default MIG welder fault

    Ok so I'll start with the fact that I know it isn't technically a MIG welder.

    So my 33 year old Hobart MIG has had a bit of an issue lately and I'd like a sanity check before I go looking.

    The transformer is staying on longer than it should. At first I thought something in the burn back timer* was going out of spec as after a few welds it would start working properly again. Last time I used it I noticed the transformer was staying on longer than the post flow gas, which if I am reading the diagrams correctly cant happen unless the problem is the contactor. So if the gas if off and the transformer is on, its the contactor right?




    *non adjustable externally on this welder. I had always thought it was adjustable internally but can't see it in the diagram.
    Attached Images Attached Images

  2. #2
    Join Date
    Dec 2018
    Location
    NSW
    Posts
    586

    Default

    So, explain the actual symptom.
    Your gas stops while the arc is still active? What's the wire drive doing?

  3. #3
    Join Date
    Jun 2012
    Location
    melbourne
    Posts
    341

    Default

    I wrote a load of useless info but have deleted it. I think you are right and the gas valve should operate at the same time as the contactor. I think the motor can switch off before both the gas and contactor for that post flow timing.
    Sorry about the silly post before.

  4. #4
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default

    Thank you guys

    Quote Originally Posted by Commander_Keen View Post
    So, explain the actual symptom.
    "The transformer is staying on longer than it should. "

    Quote Originally Posted by Commander_Keen View Post
    Your gas stops while the arc is still active? ?
    Well no, sorta. But the arc is only "out" because the wirefeed is working correctly. The transformer is still on after post flow time so there "could" still be an arch, but there isn't. You could say "the gas stops while the transformer is still active" making the question "is that possible on this welder unless the contactor is the issue?".

    Quote Originally Posted by sossity View Post
    I think you are right and the gas valve should operate at the same time as the contactor. I think the motor can switch off before both the gas and contactor for that post flow timing.
    Yes the motor does turn off before that gas/contactor. I'm pretty sure some welders and burn back and post flow as separate adjustments, But we seem to agree that on my welder there is only the one timer for both. Maybe 30 years of dust is slowing it down, just like me.

  5. #5
    Join Date
    May 2011
    Location
    Murray Bridge S Aust.
    Age
    71
    Posts
    5,942

    Default

    It pays to blow out the electronics and the liners from time to time. For home use every other roll is what I've been told.
    When I had my business I did it on a monthly basis, surprising how much dust and crap gets in there.
    Kryn
    To grow old is mandatory, growing up is optional.

  6. #6
    Join Date
    Jan 2004
    Location
    Mackay North Qld
    Posts
    6,446

    Default

    Quote Originally Posted by Stustoys View Post
    The transformer is staying on longer than it should.
    What is the indication that the transformer is still operating. Is it the clack of the coil electromagnet releasing or a just the hum of the transformer?

    Given that your mig is old and like all migs operated in a metallic dust environment what's the chances of the contact points being arced and pitted.

    It would follow that point damage would slow down the shut down/close off sequence, I would have thought.

    I do recall mention of a contactor replacement talked about on one of the UK mig welding forums. The brand name part was not available but a suitable substitution was available.

    Just some food for thought. A thirty three year run is not too bad compared to the longevity or lack of it, in some of today's products.


    Grahame

  7. #7
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default

    It has been blown out a few times over the years, but I wouldn't say "often" by any means.

    Quote Originally Posted by Grahame Collins View Post
    What is the indication that the transformer is still operating. Is it the clack of the coil electromagnet releasing or a just the hum of the transformer?
    Its the burnback going long. Transformer humming, then contactor clicks and humming stops.
    Quote Originally Posted by Grahame Collins View Post
    Given that your mig is old and like all migs operated in a metallic dust environment what's the chances of the contact points being arced and pitted.

    It would follow that point damage would slow down the shut down/close off sequence, I would have thought.
    As it "clears" itself my guess is its just the movement of the contactor, I'd guess if it was pits it wouldn't "clear".... but thats just a guess. An airline with some extra attention to the contactor sometime in the next week should sort something out, and I'll get some part numbers while I'm in there in case it comes back.
    Quote Originally Posted by Grahame Collins View Post
    Just some food for thought. A thirty three year run is not too bad compared to the longevity or lack of it, in some of today's products.
    Given that for the price of this unit* I could have bought a $300 welder and replaced it every 3 years I should hope it would!!


    *I got the welder cheap due to a phone call by a friendly TAF teacher to one of their suppliers. Though granted hobby MIGs were not a thing then. And thats excluding interest that could have been earned.

  8. #8
    Join Date
    Oct 2006
    Location
    Armidale NSW
    Age
    52
    Posts
    915

    Default

    It does sound like the contactor is sticking. One way to be sure is to measure the contactor coil voltage. If it goes to 0V and the contactor is still on then the contactor is sticking, otherwise it's an issue with the control electronics.

    Note there are dangerous (lethal) voltages inside welders so be especially careful, or get an experienced person to look at it for you..
    Cheers.

    Vernon.
    __________________________________________________
    Bite off more than you can chew and then chew like crazy.

  9. #9
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default

    Seems there is more going on here than I thought.
    Fingers crossed on the contactor.
    Will likely be a few days before I can start looking and as is "comes good" if I don't catch the fault in the first X tries before it comes good I've no idea how long I have to wait to try again. I have a few things to try. Longest shot, I'll manually operate the contactor and see if hangs..... couldn't be that lucky could I?

  10. #10
    Join Date
    Mar 2011
    Location
    Southern Flinders Ranges
    Posts
    1,536

    Default

    Yes, if the gas is off and the transformer is still on your problem is the contactor. Control for both comes from the triac on the control board, if one is working as expected the controller is working normally.

  11. #11
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default

    The tax man will have to wait a little longer until I get my return done. Went to the shed this morning with a collection of paper work and meters.

    Well the longest shot came in, though I could have found a better screwdriver.
    https://www.youtube.com/watch?v=7y_zofmgJMc

    Din mount and opens up very easily. Quick blow out and everything is working as it should for now. I guess I'll find out in a couple of weeks if the problem will return. At least I know what replace if it does. Checked a few other things while I was in there but they all appear fine.

    Thank you all

  12. #12
    Join Date
    Sep 2012
    Location
    York, North Yorkshire UK
    Posts
    6,436

    Default

    Hi Stuart,

    Some of those contactors, not all, can be easily disassembled and the coil and armature separated and the anvil cleaned. A layer of dust or dirt under the armature will cause the problem that you illustrated in the video. You shouldn't have to remove the wiring either, the contact block usually just lifts off bringing the coil and armature with it.

    A lot cheaper than a replacement.
    Best Regards:
    Baron J.

  13. #13
    Join Date
    Aug 2011
    Location
    Melbourne
    Posts
    4,779

    Default

    Glad you got it sorted Stu.

    Simon

    Sent from my SM-G970F using Tapatalk
    Girl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.

  14. #14
    Join Date
    Jul 2010
    Location
    Melbourne
    Posts
    9,088

    Default

    Quote Originally Posted by BaronJ View Post
    Some of those contactors, not all, can be easily disassembled and the coil and armature separated and the anvil cleaned.
    This one was. Pretty much the same squeeze used to get it off the Din rail is used to open it.
    Good for another 33 years.
    Still I learnt a bit about just whats going on on that board.

Similar Threads

  1. Intermittent pump fault
    By Stustoys in forum ELECTRICALS
    Replies: 15
    Last Post: 1st Sep 2019, 11:51 AM
  2. It's Stuart's Fault. An Optical Acquisition.
    By Anorak Bob in forum METALWORK GENERAL
    Replies: 37
    Last Post: 4th Dec 2013, 12:48 PM
  3. QUEENSLAND Cig welder transarc tradesman HD (stick/arc welder) 3phase
    By dkaoffroad in forum METALWORK - Machinery, Equipment, MARKET
    Replies: 0
    Last Post: 8th Jun 2013, 10:45 AM
  4. welder
    By brendon17 in forum METALWORK GENERAL
    Replies: 10
    Last Post: 8th Jun 2012, 10:23 AM
  5. dial fault
    By nadroj in forum THE HERCUS AREA
    Replies: 12
    Last Post: 27th Jun 2011, 12:00 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •