Results 1 to 6 of 6
  1. #1
    Join Date
    Aug 2019
    Location
    Revesby - Sydney Australia
    Age
    56
    Posts
    1,183

    Default Anyone used Power Feed setup for CNC?

    Factory neighbour has a large Hafco mill (BM-40 or 30) that he has asked about adding some CNC abilities to. He is not real computer savvy, so I will be looking for a non-PC based solution. Maybe a tablet, or LinuxCNC on an embedded device.


    The easy way would be to add big stepper motors and some toothed belts, but that prevents manual use unless they are disconnected again.



    I'm looking at the Power Feed motors, and DRO scales, and wondering if LinuxCNC could be configured to use these already attached motors instead of steppers?




    (I know real CNCs use DC servos, and high end ones also have additional closed loop feedback, but has anyone ever heard of one without direct feedback from the screw motors?)

  2. #2
    Join Date
    Nov 2017
    Location
    Geelong, Australia
    Age
    57
    Posts
    2,651

    Default

    I can’t see that being possible - backlash and lack of ability to control small movements would be the killer.
    While it may be possible to control large movements with feedback from the scales, I can’t see it working with the relatively large on/off movements from a typical feed motor.

    Aside from the technical challenges, there would be a huge time investment to get a DIY machine to the “unskilled operator” level.
    If you didn’t get it all the way there, you would be supporting it forever.

    Personally - I wouldn’t touch it with a barge pole!!

    Proper conversion with ball screws etc for your own shop - maybe, but definitely not for a customer.

    Steve

  3. #3
    Join Date
    Jul 2016
    Location
    Melbourne
    Age
    35
    Posts
    1,522

    Default

    As Steve said, without knowing either how many steps the motors are doing or having any way to repeatably and controllably energise them like a servo or stepper you can't make anything remotely functional. Even if you have the positional feedback from the scales.

    Sent from my SM-G973F using Tapatalk

  4. #4
    Join Date
    Aug 2019
    Location
    Revesby - Sydney Australia
    Age
    56
    Posts
    1,183

    Default

    Thanks Steve. Backlash is indeed the issue with existing (Acme thread?) screws.

    (and "hunting" would be the issue with scale based closed feedback)



    Some of those power feed enclosures have speed control levers, instead of the old left/off/right lever.
    I'm not sure any of the free software supports speed control, plus backlash compensation, plus closed feedback, though



    The only CNC machining actions he asked for are milling circles and rectangles. Which is why I considered the hackiest solution.

  5. #5
    Join Date
    Jul 2016
    Location
    Melbourne
    Age
    35
    Posts
    1,522

    Default

    Milling an accurate even accurate ish circle is the hardest part of a 3 axis cnc machine. All the early point to point machines that still used trapezoidal screws could do lines and pockets okay a lot of them used multiple electronic clutch packs to take the drive from a single DC servo. Moving multiple axis simultainiously was impossible. To avoid hunting the clutches released very quickly triggered by the control. They also had hydraulic axis clamps that clamped all the non moving axis.

    I suspect with your proposed idea entering corners of pockets would be a regular hand grenade experience of smashed endmills and he would be having to manually lock all the non moving axis all the time.

    Sent from my SM-G973F using Tapatalk

  6. #6
    Join Date
    Aug 2019
    Location
    Revesby - Sydney Australia
    Age
    56
    Posts
    1,183

    Default

    As a follow up, I opened up one of these drives this week:


    I thought the forward/reverse lever was just a switch, but on this model, they are also a lever that engages the motor shaft with the small bevel gear. (i.e. the clutch, so that you can manually turn the mill axis handle without driving the power feed motor as well.)

    This means effectively the forward & reverse is electrical, but the on/off is both mechanical and electrical.

    Not easy to interface to - would need to mechanically lock the direction lever in one direction, and then override all the electronics to get fwd/rev.
    Possible, but not worth the time. Removing/selling the power drives, and adding steppers, will be much faster/easier

Similar Threads

  1. Power Feed
    By Auskart in forum METALWORK GENERAL
    Replies: 22
    Last Post: 30th Dec 2016, 08:23 PM
  2. Power Feed For My SX3 Mill
    By wm460 in forum METALWORK GENERAL
    Replies: 0
    Last Post: 29th May 2016, 05:23 PM
  3. No.O Table Power Feed
    By Anorak Bob in forum THE HERCUS AREA
    Replies: 5
    Last Post: 8th Jan 2013, 01:08 PM
  4. DM 45 power feed
    By morrisman in forum METALWORK GENERAL
    Replies: 32
    Last Post: 2nd Feb 2012, 10:34 PM
  5. power feed for a HM-45
    By Sterob in forum METALWORK GENERAL
    Replies: 2
    Last Post: 2nd Oct 2006, 08:34 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •