Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
-
31st Dec 2020, 10:30 AM #1New Member
- Join Date
- Dec 2020
- Location
- 35 partridge road monash 5342
- Posts
- 3
S16 repco power precision surface grinder service/operating manual
I wish to buy/borrow/hire a operating/service manual and hydraulic schematic drawings for this machine.
I purchased this machine from Whyalla steel mills and have restored it but I cannot get the hydraulics to work properly. can any one please help.
raym
-
31st Dec 2020, 05:30 PM #2China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 1,657
Welcome to the forum can't help with you request although remove you full address for security
-
3rd Jan 2021, 05:06 PM #3Most Valued Member
- Join Date
- Apr 2012
- Location
- Healesville
- Posts
- 2,129
-
3rd Jan 2021, 08:46 PM #4New Member
- Join Date
- Dec 2020
- Location
- 35 partridge road monash 5342
- Posts
- 3
-
4th Jan 2021, 06:24 PM #5Diamond Member
- Join Date
- Mar 2014
- Location
- South of Adelaide
- Posts
- 1,227
can you describe the problems you are having? might be able to help.
-
7th Jan 2021, 09:47 PM #6New Member
- Join Date
- Dec 2020
- Location
- 35 partridge road monash 5342
- Posts
- 3
S16 repco power surfase grinder
Hi snap trap, I have replied but must have put it in the wrong place.
When I started the machine the piston for the cross slide had sheared off the shaft,I made a new shaft and re pinned the piston, started the hydraulic motor - the cross slide would move L and R with a few seconds delay at the end of each stroke. the speed control and L and R controls appear to be functioning but slow.The grinder in\out slide does not work at all, there is oil flowing through the hydraulic motor and I can
change the direction of flow with the change over control. I removed the hydraulic motor and connected it to a power pack and it works fine, I tried reducing the bypass at the main hydraulic pump, the cross slide increased speed dramatically - too fast and the hydraulics became noisy . this machine has a hand wheel that when it is pushed in the slide can be moved manually , when I pulled the hand wheel out the machine became noisy and the hydraulic pump motor cut out on overload.
I am reluctant to start pulling the hydraulic controls apart without a diagram to show how it works.
I hope I have described things adequately and you are able to help.
I look forward to hearing from you.
Regards.
Ray Mitchell.
Similar Threads
-
Repco Surface Grinder $1200
By KBs PensNmore in forum EBAY, GUMTREE, and other off forum sales sitesReplies: 1Last Post: 10th Sep 2022, 09:34 AM -
B&S No2 manual surface grinder for sale
By jhovel in forum METALWORK - Machinery, Equipment, MARKETReplies: 9Last Post: 27th Jan 2020, 11:07 AM -
Brown and Sharpe No 2 surface grinder manual
By StrayAlien in forum METALWORK GENERALReplies: 28Last Post: 1st Oct 2016, 11:25 PM -
Repco Power type C10 cylindrical grinder
By shedeng in forum METALWORK GENERALReplies: 15Last Post: 20th Oct 2015, 03:49 AM -
How much does a Repco Power S1 Surface Grinder weigh?
By Gestalt in forum METALWORK GENERALReplies: 14Last Post: 1st Mar 2015, 07:22 PM