Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Macson surface grinder table
-
16th Jul 2019, 10:49 AM #1Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,894
Macson surface grinder table
I'd like to find a replacement for the missing single slotted table from a small Macson surface grinder.
It's fastened with four screws, and goes between the X slide and magnetic chuck.
Jordan
-
16th Jul 2019, 01:06 PM #2Golden Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 837
-
16th Jul 2019, 03:20 PM #3Most Valued Member
- Join Date
- May 2011
- Location
- Murray Bridge S Aust.
- Age
- 71
- Posts
- 5,942
Might be easier to get a block of cast and machine one up. I know it won't be original, but after a couple of coats of different paint and chipped back, who's going to know.
Getting one cast would probably cost an arm and a leg, whereas you could possibly get a block of scrap cast for $20.00 from a scrap dealer.
KrynTo grow old is mandatory, growing up is optional.
-
16th Jul 2019, 06:47 PM #4Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,894
Thanks for the thoughts.
Just worth a shot at seeing if any are out there, perhaps from a defunct machine.
-
16th Jul 2019, 08:17 PM #5Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,894
-
19th Jul 2019, 04:47 PM #6Golden Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 837
IMG_20190719_133208.jpg
Dimensions in attached image.
Will you be using the original 3 phase motor? If not, I am looking for one. Obviously there would be a cash inducement.
-
20th Jul 2019, 10:10 AM #7Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,894
-
20th Jul 2019, 12:49 PM #8Golden Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 837
-
21st Jul 2019, 04:32 PM #9Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,894
Here's some photos.
-
21st Jul 2019, 11:13 PM #10Golden Member
- Join Date
- Jul 2011
- Location
- Adelaide
- Posts
- 837
Similar Threads
-
Macson surface grinder
By Alf Scotting in forum METALWORK GENERALReplies: 19Last Post: 7th Mar 2018, 11:14 AM -
Macson 2 as surface grinder
By StrayAlien in forum METALWORK GENERALReplies: 8Last Post: 18th Sep 2016, 09:41 PM -
Macson surface grinder
By Petip in forum METALWORK GENERALReplies: 13Last Post: 26th Oct 2015, 08:02 AM -
DONE: Macson Surface Grinder
By GZBMW in forum METALWORK - Machinery, Equipment, MARKETReplies: 1Last Post: 18th May 2013, 11:14 PM -
SOUTH AUST Macson Surface grinder
By Kon R in forum METALWORK - Machinery, Equipment, MARKETReplies: 9Last Post: 22nd Oct 2012, 11:54 PM