Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
9th Nov 2020, 08:27 PM #1Novice
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 16
Vintage Bandsaw - Bronze Bushing Bearing Replacement
Hi, I've posted the beginning of a bandsaw restoration here: https://www.woodworkforums.com/f299/...oration-233432
I need to replace what I think a Forum member has identified as a sintered bronze bearing?
20201109_171049_resized.jpg 20201109_171112_resized.jpg
I Googled this and found something similar per below. Can anyone recommend someone in Brisbane who is able to supply something like or a machining shop that can replace it for me? Also what pricing could I expect?
bearing-drive-gear-bushing.jpg
-
10th Nov 2020, 03:04 PM #2Most Valued Member
- Join Date
- Nov 2017
- Location
- Geelong, Australia
- Age
- 57
- Posts
- 2,671
You might be lucky enough with the sizing to get a bush off the shelf at a bearing supplier, but likely will still need to bore or ream it to final size for the shaft after its fitted. If it was really close to the right size after fitting then its possible to remove a small amount from the bore using a scraper fashioned from a small triangular file, but its more of a "no other choice so I'll chew it to death gradually" option.
You will likely find the shaft is worn too, so depends how far you want to go with fixing it as to what you do. If its only slightly worn then it can probably just be cleaned up a bit, but if there's significant wear it probably needs to be turned undersize or replaced.
Don't buy a bush without evaluating the shaft first or you'll likely end up with a bush that needs a smaller bore!
I just turned up a standard bronze bush (not sintered) for my Thiel bandsaw. Added the oil grooves like yours has.
Any machine shop could do the job, but may not be cheap depending on whether or not they want the job.
Your best bet might be a local friendly member on here that is happy to do it for a chat and liquid payment
Steve
-
10th Nov 2020, 08:44 PM #3Most Valued Member
- Join Date
- May 2011
- Location
- Murray Bridge S Aust.
- Age
- 71
- Posts
- 5,959
Hi Charlie, when you take the wheel for the bushing, take the shaft as well. They should be able to tell you if the shaft requires attention or not.
KrynTo grow old is mandatory, growing up is optional.
-
3rd Jan 2021, 09:49 PM #4Novice
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 16
Thanks all - all sorted:
-
3rd Jan 2021, 10:25 PM #5Most Valued Member
- Join Date
- Nov 2017
- Location
- Geelong, Australia
- Age
- 57
- Posts
- 2,671
Looks good!
With it being a WW saw and the top pulley you’re probably better with grease as there’s the possibility that oil could drip onto the piece you’re cutting and spoil it.
Steve
-
6th Jan 2021, 09:54 AM #6Novice
- Join Date
- Apr 2013
- Location
- Brisbane
- Posts
- 16
Thanks Steve, yes good point. I'm not that keen on the oil route.
-
6th Jan 2021, 12:09 PM #7Senior Member
- Join Date
- Jul 2017
- Location
- Burleigh heads QLD
- Age
- 29
- Posts
- 114
I'm in Burleigh heads and should have the right size bronze hollowbar in LG2 to machine a new bush up, check the shaft size to, if you're lucky I'll have some ground 4140 in the size. if you get in any strife just give me a bell on the landline 0755221726
Similar Threads
-
GMF grinder bearing replacement
By monchochos in forum METALWORK GENERALReplies: 22Last Post: 3rd May 2019, 12:18 PM -
Lathe Spindle Bearing Replacement
By Dingo Dog in forum METALWORK GENERALReplies: 7Last Post: 6th Nov 2017, 01:13 AM -
Cheap bushing/bearing options for an 85mm shaft?
By gallegos in forum METALWORK GENERALReplies: 10Last Post: 29th Nov 2013, 04:19 PM -
Bronze Spindle Bearing Shells
By electrosteam in forum THE HERCUS AREAReplies: 28Last Post: 26th Oct 2012, 09:39 PM -
Bearing bronze
By Tiger in forum METALWORK GENERALReplies: 7Last Post: 31st May 2008, 05:52 PM