Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Confusion
-
17th Oct 2021, 08:06 PM #1Golden Member
- Join Date
- Jan 2016
- Location
- Wodonga Vic
- Age
- 38
- Posts
- 633
Confusion
Backstory,
12 months ago I had to replace the cylinder head on my courier ute, Repco salesman recommended and sold me some Permatex No1 for the gaskets/cover plates etc.
I soon noticed that wherever it was in contact with oil or coolant it was breaking down into a mess of brown goo and fluids were weeping everywhere it was used, and the places it was subject to heat it turned brittle and fell apart.
This weekend I had to pull the head because of a big coolant leak up under the intake manifold, it appeared to be pouring out of the head gasket and on inspection I found the head gasket was blown (as expected)
The strange thing is, I found a mass of coolant soaked brown goo inside the bottom of cylinder 3 intake port, near the crack in the head gasket.
I can't figure out how it got there and if the two are related, hope I'm not just treating the symptom instead of the real problem by putting a new head gasket on
IMG_1741.jpgIMG_1742.jpgIMG_1748.jpg
-
17th Oct 2021, 09:34 PM #2Most Valued Member
- Join Date
- Nov 2017
- Location
- Geelong, Australia
- Age
- 57
- Posts
- 2,651
I’m a big fan of the non-setting Permatex #3 for coolant related sealing, but no experience with the #1.
It looks like #1 is a similar product - but sets hard.
The #3 definitely isn’t affected by coolant. I normally use silicon for oil areas so can’t comment on that aspect.
I’ve done a few heads and gaskets over the years but never seen a gasket in basically good condition with a clean crack like that.
What was the reason for the head replacement previously? Any chance the block is cracked there?
Steve
-
17th Oct 2021, 09:56 PM #3Golden Member
- Join Date
- Jan 2016
- Location
- Wodonga Vic
- Age
- 38
- Posts
- 633
Hi Steve, It's possible that the damage occurred when I lifted the head off but I was pretty careful and don't think I caused that damage.
The original head was diagnosed by my local mechanic to have a cooked valve, so I took it home and put a new head on it.
I'm starting to think maybe the new head has cracked, I drove the car without knowing it had lost a good amount of coolant, or maybe the block! I'll clean it up and see if I notice anything. the metallurgists at work do crack testing so maybe they have stuff I can take home and test for cracks.
I'm just stumped what the buildup is and why it's there, maybe it's worse than I first thought...
-
17th Oct 2021, 10:17 PM #4Most Valued Member
- Join Date
- Nov 2017
- Location
- Geelong, Australia
- Age
- 57
- Posts
- 2,651
Confusion
FWIW - Apparently mixing different types of coolants can produce a jelly/snot substance.
If you can get hold of a dye penetrant crack test kit would be useful.
They are about $90 to buy, but hopefully you can sweet talk the blokes at work
Steve
-
17th Oct 2021, 11:20 PM #5Diamond Member
- Join Date
- Oct 2008
- Location
- N.W.Tasmania
- Posts
- 1,407
Absolutely agree on the dye check system, If you can't borrow a set, but can buy the individual cans, just get the dye penetrant. You can clean with any suitable solvent, Prepsol, turps, brakeClean etc and for the developer, sprinkle chalk dust, as in engineering chalk dust, whiting etc. You could borrow the kitchen flour sifter, or if the war Dept. has other ideas a salt shaker from a charity shop would do, or even just jar with a tin lid with a couple of small holes punched in.
I have used and found very satisfactory Permatex number 2, I have no experience of the other varieties.
-
17th Oct 2021, 11:36 PM #6
info
The data sheet says not to use it in contact with any additives: maybe your coolant additive messed up the #1 stuff
https://www.permatex.com/wp-content/.../tds/80008.pdf
The #3 non-hardening stuff is excellent , I have used in on old Land Rover engines that normally leak like a sieve
-
19th Oct 2021, 11:15 PM #7Golden Member
- Join Date
- Jan 2016
- Location
- Wodonga Vic
- Age
- 38
- Posts
- 633
So rather than taking a chance and having to do the job all over again down the road I took the head and old gasket to a local engine reconditioning business.
I told him I blew the gasket and I was worried I might have damaged the head, he looked it over and said it all looks good with no signs of the head having overheated, he then looked at the head gasket and said it was absolute $h!t quality and no surprise it failed (shows what I know, I thought it looks decent when I put it on)
he ordered me a new graphite gasket and is cleaning the head before I put it back on.
I got lucky this time.
cheers
-
20th Oct 2021, 01:11 AM #8Most Valued Member
- Join Date
- May 2011
- Location
- Murray Bridge S Aust.
- Age
- 71
- Posts
- 5,943
I only use REPCO as a LAST resort, when no one else has or can get the part, we have 4 suppliers here.
In case you didn't know, REPCO stands for Rip Every Poor Customer Off, or similar.
KrynTo grow old is mandatory, growing up is optional.
-
29th Oct 2021, 03:25 PM #9Most Valued Member
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,910
Similar Threads
-
4140 confusion
By morrisman in forum METALWORK GENERALReplies: 4Last Post: 23rd Apr 2021, 09:55 PM -
single to 3 phase vsd confusion.
By lather in forum METALWORK GENERALReplies: 117Last Post: 9th May 2020, 07:38 PM -
MIG wire confusion
By twebb01 in forum WELDINGReplies: 19Last Post: 9th Jun 2012, 12:46 PM -
Helical gear confusion
By Ueee in forum METALWORK GENERALReplies: 4Last Post: 10th Apr 2012, 01:10 PM -
CONFUSION - Doorstops missing
By DanP in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 17Last Post: 12th Dec 2003, 12:34 PM