Results 76 to 90 of 134
Thread: Show me your Anvil thread...
-
27th Oct 2018, 09:56 PM #76Intermediate Member
- Join Date
- Feb 2018
- Location
- Perth. Australia
- Age
- 63
- Posts
- 27
Bisalloy. Can you recommend a grade Dsel?
-
19th Nov 2018, 08:40 PM #77Golden Member
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 667
not strictly and anvil but you still use it for smith'n - finally got around to making a stand for my swage block. even used it today, and not for just putting stuff on (like a table).
swageIMG_1814.jpg
-
8th Dec 2018, 06:02 PM #78
Lots of blokes have anvils but not a lot have a swage block.
Good post.
Grahame
-
8th Dec 2018, 08:51 PM #79
Hi Mark,
It's not Dsel but Grahame. Maybe use bisalloy 80 if you can access some offcut at scrap value.
They don't sell it in anvil sized pieces, rather big sheets.
In that case it would be far cheaper to just buy your anvil.
I was fortunate in that I had access to a scrappy who was buying scrap from some of the Mackay based Dragline bucket repair shops.
It was as a strip of 450mm long x 70mm x 75mm. Also, I was fortunate at the time to have access to oxy cutting and heavy welding eqpt. I made the base of 20mm structural plate under a 150 ton brake press.
You need to evaluate what types of steel your scrappy can access.
cheers
Grahame
-
23rd Dec 2018, 11:54 PM #80Intermediate Member
- Join Date
- Feb 2018
- Location
- Perth. Australia
- Age
- 63
- Posts
- 27
Thanks for the recommendations Grahame.
-
23rd May 2019, 10:32 AM #81Novice
- Join Date
- May 2019
- Location
- North Perth
- Posts
- 23
WA Midland Railway Workshop Anvil
Bought this anvil about 5 years ago, seller told me he believed it came from the WAGR workshops in Midland. Had to buy it as my Dad was a fitter and turner there from after the war (WWII) until he retired. It has 1 0 3 stamped on side so 115 lbs or about 56 kgs. No other identifiers so it may have been cast at the workshops.
I have cleaned the dings with a flap wheel, painted it and made the block, it has magnets to deaden the ring you can just see one next to Pritchel hole , I am inner city so the noise is an issue. In the picture you may be able to see two hardy hole inserts I made one with reo to give leaves some veining the other is a fuller and I have another similar sharpened up for hot setting it is on the back of the block. They are both made from leaf spring steel. You can also see my gas forge which replaced a charcoal forge I made but sold to save space.
i have another forge at an old fibro beach house in Busselton, that has a brake drum charcoal forge and a farriers anvil I bought new about 20 years ago. I may take some photos of that and post later.
The other photo is my new fly press which hasn’t been used yet I am tooling it up and making a stand to get it up off the floor. It is a Sweeney and Blocksidge and based on screw diameter (2 1/2”) it is approx a number 10 so should be able to give about a 10 ton whack. The weights are my addition the ball weights were missing, the shiny new clamping bed is mine and you can see a dishing tool I made from a tow bar. The tool holder I drew up but had machined. The tool in holder is a cutter I made from a piece of coil spring braised on to a 1” bolt to fit in the holder and spread the impact through the bolt head. Intend to make a curve bender for gate tops next and a small right angle bender.
The power hacksaw in background is fairly new got it about six months ago had to replace the motor with single phase and put in a coolant pump. It is part of another thread.
Toots1.jpg Toots2.jpg
-
23rd May 2019, 02:41 PM #82Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,189
I fixed the orientation for you this time.
-
23rd May 2019, 06:23 PM #83Novice
- Join Date
- May 2019
- Location
- North Perth
- Posts
- 23
-
23rd May 2019, 08:03 PM #84Golden Member
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 667
I like the look of that fly press, can do quite a lot wi th them.
I use mine for forging and bending mostly. Also good for punching hammer eyes.
-
23rd May 2019, 08:22 PM #85Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,189
I downloaded your photos and used a very expensive photography program called Photoshop to correct the rotation and the uploaded them again. For correcting image rotation using Photoshop is a bit like using an elephant gun on a mouse. Others may be able to give some budget level ideas.
-
23rd May 2019, 11:23 PM #86Novice
- Join Date
- May 2019
- Location
- North Perth
- Posts
- 23
Fly press
I have to admit I like making tools more than things but I do make stuff. The press only cost me $300 so less than my small anvil and I can see it being equally useful. Probably won’t make any hammers, I like using old hammers. My last big project was my neighbors’ front fence. Some forging but lots of welding.
Love to to hear more about your press, tooling and what you have done with it.
cheers Peter
-
18th Oct 2019, 08:48 PM #87Intermediate Member
- Join Date
- May 2016
- Location
- AU
- Posts
- 30
Here's our anvil, plus one of our non-anvil anvils.
The first pic is a small anvil, about 280mm from heel to horn. It was used by my partner's great grandfather who used to be a jack of all trades in country Victoria. He had an Indian with a sidecar in which he carried around his tools. He was also an apiarist.
Marked John Forrest. Anyone know more about these?
The second pic is of one of our non-anvil anvils. A heavy rail tie I think. Very heavy and great for bashing stuff on. The rounded bit is kind of like a horn.
Me and my eldest son did a few intro to blacksmithing days at the forge at Bundoora a few years back. Recently the kids have decided they want to get back into it, so we're setting up a forge out the back of the shed.
Martin
Sent from my H4133 using Tapatalk
-
19th Oct 2019, 11:48 AM #88Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,189
I thought I should ddd my Anvil to this thread.
Gets used a lot - not so much for smithing
IMG_3847.jpg
And my Swage Block.
I've used it only a few times
IMG_5843.jpg
-
19th Oct 2019, 08:12 PM #89Golden Member
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 667
HI Martin,
Nice looking Anvil what its weight?
Looks like an english made Anvil - no reference in my resources to John Forrest, whats the text just above the JF?
Cheers
steve
-
19th Oct 2019, 08:43 PM #90Senior Member
- Join Date
- Jun 2016
- Location
- Sydney
- Posts
- 283
Miniature 'anvil'
It's not an anvil really, but it is good for hammering on. It looks like a 150 mm length of 75 mm round steel rod sitting up on a square base - but that is not the full story. I tried to cut it and, well, failed really. Turns out it and its identical mate were hardened steel link pins out of some large hydraulic machinery. Kinda heavy, but it is portable.
Cheers
Roger
Similar Threads
-
Anvil on e Bay
By auscab in forum THE SMITHYReplies: 6Last Post: 28th Jan 2013, 10:34 PM -
SOLD: Anvil
By ranga_rod in forum METALWORK - Machinery, Equipment, MARKETReplies: 2Last Post: 25th Nov 2012, 04:15 PM -
TASMANIA Anvil
By rwatson in forum METALWORK - Machinery, Equipment, MARKETReplies: 1Last Post: 17th Apr 2011, 07:40 PM