Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 5 of 5

Thread: Hafco al330

  1. #1
    Join Date
    Jul 2007
    Location
    sandstone point queensland
    Age
    69
    Posts
    182

    Default Hafco al330

    HAFCO al330 lathe in good condition,comes with stand,milling attachment,quick change toolpost and 6 tool holders,lots of
    tooling as shown,40mm hollow shaft with m3 adaptor,drill chuck,live centre,centre,other bits and pieces,water mist cooling system ,has new belts and motor start capacitor,
    decals are a bit poor because someone (me) used kero to clean it years ago ,am looking to get around $2200,all in good condition,also have book,SANDSTONE POINT QLD,

    Attached Images Attached Images

  2. #2
    Join Date
    Jan 2004
    Location
    Mackay North Qld
    Posts
    6,446

    Default

    To all,

    Read these full Market Rules before anyone doing any business here on this sub Forum.

    Do not do anything else BEFORE you read them. You have been reminded.

    If you don't understand any of them, ask, before you act.

    https://metalworkforums.com/f90/t202688-market-rules

    No excuses accepted if it goes bad on you.

    Grahame

  3. #3
    Join Date
    Jul 2007
    Location
    sandstone point queensland
    Age
    69
    Posts
    182

    Default

    Quote Originally Posted by Grahame Collins View Post
    To all,

    Read these full Market Rules before anyone doing any business here on this sub Forum.

    Do not do anything else BEFORE you read them. You have been reminded.

    If you don't understand any of then ask, before you act.

    https://metalworkforums.com/f90/t202688-market-rules

    No excuses accepted if it goes bad on you.

    Grahame
    is there a problem with this post Grahame?

  4. #4
    Join Date
    Jan 2004
    Location
    Mackay North Qld
    Posts
    6,446

    Default

    Quote Originally Posted by robyn2839 View Post
    is there a problem with this post Grahame?
    No problem with the post as yet, but please see previous post "Taps, Dies and Reamers" in its entirety and you see why I have placed this notice notice and will continue to do so for all new posts for a while. Its an "ounce of prevention is better than a pound of cure", type thing.

    Grahame

  5. #5
    Join Date
    Jul 2007
    Location
    sandstone point queensland
    Age
    69
    Posts
    182

    Default

    sold thankyou

Similar Threads

  1. replacing control switch for AL330 lathe
    By robyn2839 in forum ELECTRICALS
    Replies: 4
    Last Post: 28th Aug 2019, 08:17 PM
  2. Hafco al330 metal lathe
    By robyn2839 in forum METALWORK - Machinery, Equipment, MARKET
    Replies: 4
    Last Post: 9th Jun 2019, 10:07 PM
  3. N.S.W. Hafco AL330 Metal Lathe LOC: Coffs Harbour NSW
    By BenM78 in forum METALWORK - Machinery, Equipment, MARKET
    Replies: 0
    Last Post: 8th Jan 2013, 05:42 PM
  4. AL330 manual
    By RayG in forum METALWORK GENERAL
    Replies: 9
    Last Post: 7th Jul 2012, 03:33 AM
  5. Hafco al 900
    By LOTUS in forum METALWORK GENERAL
    Replies: 0
    Last Post: 17th Sep 2005, 04:26 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •