Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
-
5th May 2019, 08:17 PM #1Philomath in training
- Join Date
- Oct 2011
- Location
- Norwood-ish, Adelaide
- Age
- 59
- Posts
- 6,561
MT1 milling cutters and large lathe tool
At the moment, I seem to be collecting surplus from other members which means some of mine needs to go...
First up is a large lathe tool. Top to bottom measurement of the shank is around 35mm. This is a thread cutting tool that can be adjusted for thread helix angle, and the inserts can be sharpened easily as they are a tangential tool. I vaguely recall buying it on ebay thinking it was smaller than it was, but it does not fit in any tool holder I have.
P1040524.jpg P1040523.jpg
These came in a box of 'misc. tooling' that someone presented me with. The 3 cutters are all MT1 fittings, with 2 off 3/8" (1 off draw bar, 1 off tang'd) cutters and 1 off 5/16" (draw bar). Sitting next to it is a pass through sleeve, MT1 to MT2.
P1040522.jpg
Asking $30 for the lathe tool and $20 for the cutters. The sleeve I'd like $10 for, but will give first refusal to whoever wants the cutters.
Michael
-
5th May 2019, 08:18 PM #2Most Valued Member
- Join Date
- Jul 2016
- Location
- Melbourne
- Age
- 35
- Posts
- 1,522
I'll take the lot if that's okay. I just found the astoba is mt1.
Sent from my Nokia 8 Sirocco using Tapatalk
-
5th May 2019, 08:22 PM #3Philomath in training
- Join Date
- Oct 2011
- Location
- Norwood-ish, Adelaide
- Age
- 59
- Posts
- 6,561
By 'the lot', do you mean you want the lathe tool too, or just the cutters and sleeve?
Michael
-
5th May 2019, 08:30 PM #4Most Valued Member
- Join Date
- Jul 2016
- Location
- Melbourne
- Age
- 35
- Posts
- 1,522
The lathe tool as well if that's okay.
Sent from my Nokia 8 Sirocco using Tapatalk
-
5th May 2019, 09:20 PM #5Philomath in training
- Join Date
- Oct 2011
- Location
- Norwood-ish, Adelaide
- Age
- 59
- Posts
- 6,561
All sold then.
-
7th May 2019, 08:05 PM #6Senior Member
- Join Date
- May 2019
- Location
- Picnic Point, Sydney
- Age
- 77
- Posts
- 314
I just threw out about 100 new, new reground and barely used milling cutters with morse tapers ranging from 1/4" to 1 1/4" in long and short series.
I didn't think anyone used taper mount cutters any more.
Similar Threads
-
source for quality lathe and milling cutters
By Pumpkinate in forum METALWORK GENERALReplies: 6Last Post: 14th Sep 2018, 10:22 PM -
Indexible milling cutters
By morrisman in forum METALWORK GENERALReplies: 11Last Post: 6th Aug 2015, 09:08 AM -
Threaded milling cutters
By morrisman in forum METALWORK GENERALReplies: 18Last Post: 28th Sep 2011, 03:37 PM -
Holders for milling cutters
By Tiger in forum METALWORK GENERALReplies: 4Last Post: 11th Oct 2009, 02:13 PM -
I'm after some odd milling cutters
By funkychicken in forum METALWORK GENERALReplies: 10Last Post: 4th Sep 2009, 09:28 PM