Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Page 3 of 3 FirstFirst 123
Results 31 to 36 of 36
  1. #31
    Join Date
    Aug 2009
    Location
    Sydney, NSW, Australia
    Posts
    1,836

    Default

    Hi guys me again, Does anyone know how long it takes for 6061 or 6082 both T6 to self harden i i anneal it?

  2. #32
    Join Date
    Sep 2010
    Location
    Lebrina
    Posts
    1,910

    Default

    I take it that you want to anneal so as to make the bending easier. If you anneal the material, you will be left with a material of unknown mechanical properties and ageing will restore only some of the properties. Altogether not a good idea when you consider the planned use of the section and another reason supporting my original statement that Aluminium trailer design is not for the faint of heart and opens the proverbial pandoras box.

  3. #33
    Join Date
    Aug 2009
    Location
    Sydney, NSW, Australia
    Posts
    1,836

    Default

    Hey Karl, Thanks or the post i need to make one 20 degree bend per each side of the i beam i can cold bend it over 1.2 meters at 16 degrees i than tried to bend that same bend to 19.1 degrees but see the picture below at 19.1 degree's it gets a grainy look on the outside, however 16 degree's is fine there is no markings

    pictured is the length of i beam i have been testing with so far to see what i could get from it
    Attached Images Attached Images

  4. #34
    Join Date
    Sep 2010
    Location
    Lebrina
    Posts
    1,910

    Default

    Quote Originally Posted by gazza2009au View Post
    Hey Karl, Thanks or the post i need to make one 20 degree bend per each side of the i beam i can cold bend it over 1.2 meters at 16 degrees i than tried to bend that same bend to 19.1 degrees but see the picture below at 19.1 degree's it gets a grainy look on the outside, however 16 degree's is fine there is no markings

    pictured is the length of i beam i have been testing with so far to see what i could get from it
    Is it just an optical illusion or are those two bends at very different radii? It looks like one is a lot tighter than the other. I would have expected 20 degrees to be easily attainable provided the radius was nice and gentle. Having seen your earlier post re bending the I beam in your press, I reckon your method needs some fine tuning. I reckon you need to make a radius former similar to a pipe bender so as to get a gentle and consistent bend radius. Having said that, you may well struggle to bend that way in a workshop press with limited stroke available.
    I definitely wouldn't anneal the section as you would then be working with very much an unknown quantity. I have done it for non critical components, but would not be keen for the main runners of a boat trailer.

  5. #35
    Join Date
    Aug 2009
    Location
    Sydney, NSW, Australia
    Posts
    1,836

    Default

    2 different radius's Karl it was just a test piece i actually made 3 bends on this piece, first bend was 16 degrees, second bend was on the existing 16 to 19.1 degrees than i tried to use my die on the other radius

    I'm going to refine the die i built and use more of a curve instead of the points I'll grind down the welds and run some 5mm flat bar around the radius supporting it where needed and see how i go bending again

    i still have another length of i beam that hasn't been bent yet so i will make sure i have a better die before i try it

    thanks for helping out Karl and everyone else i really appreciate the advice and help

  6. #36
    Join Date
    Aug 2009
    Location
    Sydney, NSW, Australia
    Posts
    1,836

    Default

    Capral sells a few sizes of i beam can someone give advice to best size to use? There is
    100mm 6082 T6, https://www.1800aluminium.com.au/cat...sult/?q=998273
    101mm 6061 T6, https://www.1800aluminium.com.au/cat...sult/?q=841161
    130mm 6082 T6, https://www.1800aluminium.com.au/cat...sult/?q=998274
    216mm 6082 T6, https://www.1800aluminium.com.au/cat...sult/?q=808121

Page 3 of 3 FirstFirst 123

Similar Threads

  1. Plan Drawers - Canberra
    By Blu_Rock in forum EBAY, GUMTREE, and other off forum sales sites
    Replies: 1
    Last Post: 28th Jul 2014, 05:14 PM
  2. Engraving Lines - A Plan
    By Anorak Bob in forum METALWORK GENERAL
    Replies: 12
    Last Post: 28th Aug 2012, 10:06 AM
  3. Plan B?
    By Sawmaster in forum WELDING
    Replies: 4
    Last Post: 22nd Dec 2010, 11:49 AM
  4. Plan B trailer build
    By Franklin in forum TRAILERS & OTHER FABRICATED STUFF
    Replies: 40
    Last Post: 7th Sep 2010, 11:03 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •