Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 25
Thread: My welders are breeding.
-
1st Aug 2020, 09:00 AM #1Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 6,216
My welders are breeding.
It seems my welders are breeding.
Some weeks ago at an online auction I bid on and won a Miller Thunderbolt 300 amp AC stick welder. It is a welder that is single phase, but is 240V or 415V input. It also came with a heap of welding rods and I have found I like 7014 rods. It will probably get converted to running a lathe, as I can input 240V and tap 415V off it, then use that to run a VFD connected to a lathe.
Then I go out and buy a portable Unigmig 250MTS for mig welding in the field. It seems really good and probably is the best welder I own going by the arc it runs. It also seems to be highly efficient as turn the stick up to full power and I can burn holes in everything, all from a 15 amp socket, although it says to use a 32 amp.Gold, the colour of choice for the discerning person.
-
1st Aug 2020, 09:20 AM #2Most Valued Member
- Join Date
- Aug 2011
- Location
- Melbourne
- Posts
- 4,779
Hi RC,
What a problem to have!
Wrt using your welder as an step up converter (is that what you would call it?)
I have an old Goodwell AC arc welder which has multiple input taps, 240 & 415 from memory. Are you suggesting it may be possible for me to wire that to get 415 out of a 240v input?
(Hey Mods time for the massive disclaimer bit!)
Simon
Sent from my SM-G970F using TapatalkGirl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.
-
1st Aug 2020, 09:52 AM #3Most Valued Member
- Join Date
- Mar 2011
- Location
- Southern Flinders Ranges
- Posts
- 1,536
If it has seperate windings for the 415 and 240 depending on how it’s wound and assembled, yes it might be possible. The two input windings would need to be assembled onto the core in the same fashion as the traditional primary and secondary relationship between input and low voltage secondary are. So assuming they were, you also need to keep in mind the voltage vs current relationship that applies when using a transformer which is in this case as it’s a step up, as voltage ones up, available current goes down. Your step ratio is 1.7:1 so if you want 10A at 415V the 240V Side must be capable of delivering 17A plus any losses, which in an iron core transformer will be anywhere up to 30%, so you could comfortably suggest around 23A would be required at the input winding.
More likely the input winding is a tapped winding in which case no it is not possible.
-
1st Aug 2020, 10:15 AM #4Most Valued Member
- Join Date
- Nov 2017
- Location
- Geelong, Australia
- Age
- 57
- Posts
- 2,651
If the inputs are a single tapped winding it will still work. It’s effectively an auto transformer.
Steve
-
1st Aug 2020, 10:44 AM #5
Know them feels.
Nothing quite matches new welder day IMO.
Picked up my new one last week myself. A German 180a multi process pulser by EWM. One of the nicest arcs I've had the pleasure of making to date. Particularly so as a single phase machine.
-
1st Aug 2020, 10:44 AM #6
-
1st Aug 2020, 11:18 AM #7Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 6,216
Gold, the colour of choice for the discerning person.
-
1st Aug 2020, 04:48 PM #8Most Valued Member
- Join Date
- Mar 2011
- Location
- Southern Flinders Ranges
- Posts
- 1,536
-
1st Aug 2020, 04:53 PM #9Most Valued Member
- Join Date
- Aug 2011
- Location
- Melbourne
- Posts
- 4,779
Thanks for the replies.
So the welding connections don't get used. They basically become a spectator winding?
Simon
Sent from my SM-G970F using TapatalkGirl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.
-
2nd Aug 2020, 12:03 AM #10Diamond Member
- Join Date
- Oct 2008
- Location
- N.W.Tasmania
- Posts
- 1,407
That's correct Simon, at least on any 240/415 Volt input welder I have seen. The primary winding is effectively an auto transformer, so you get no isolation, but a lot less copper is needed to wind the winding, than would be the case where you had two seperate windings, electrically isolated but magnetically coupled. I have often wondered if they could be used to build a rotary phase converter, but have felt that I would probably need a conventional transformer, that is one with seperate windings for the 240 volt winding and another winding for the 415V. It seems to me that with the Australian system having the neutral leg at ground potential, I would never get that leg to get anywhere near 415v without having an isolation transformer to get my 415 volts. That won't be a problem for Richard however if he uses a VFD to generate the three phases, and since VFDs are so much cheaper now and come with lots of useful features, the attraction of a rotary phase converter is lessened even though it can run multiple machines simultaneously.
-
2nd Aug 2020, 09:12 AM #11Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 6,216
Gold, the colour of choice for the discerning person.
-
2nd Aug 2020, 11:42 AM #12
OK ! Here it is,then.
DISCLAIMER
No liability is accepted by U-Beaut or the Metalwork Forum's administrators
or moderators for advice offered by members posting replies
or asking questions regarding electrical work.
We strongly advise contacting a Licensed Tradeperson for all electrical work.WARNING
Information supplied within posts is not to be considered as detailed formal instructions to complete a task.
Members following such information do so at their own risk
-
7th Aug 2020, 02:04 PM #13Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 6,216
Well there is one downside to this Mig, stick, Tig welder.
They decided to put something called Voltage Reduction Device on the stick setting. I have renamed it to make rods stick device.
An absolutely stupid thing to have without a switch to turn it off. The whole point of welders OCV is to make it easier to strike the arc.Gold, the colour of choice for the discerning person.
-
7th Aug 2020, 05:43 PM #14Most Valued Member
- Join Date
- Aug 2011
- Location
- Melbourne
- Posts
- 4,779
Yea I learnt about that feature when looking into my last stick welder purchase.
Is it designed to reduce the chance of electricusion of the operator if they touch both the clamp and electrode end?
Simon
Sent from my SM-G970F using TapatalkGirl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.
-
7th Aug 2020, 06:53 PM #15
IIRC the OCV on non vrd welders can be up around 60V. Some electrodes will specifiy a minimum OCV for operation.
VRD IS a protection device.
It is often required for workplace environments where it is a WHS requirement. They usually have a protection rating that is linked to the type of environment they are able to be used in from a WHS risk management point of view- category A B or C (cat c is when the operator is in contact with the job, and temp > 35 degrees c- ie climbing all over the job in hot summer heat). I can't recall the actual requirements of the australian standard, but having the ability to switch it off may mean that the manufacturer is no longer compliant to the standard.
YMMV if all this is applicable for you, as with most things... But the big idea is to stop you copping the full 200A and popping your eyeballs if you are somehow stupid enough to put yourself as the path of least resistance between the earth clamp and the electrode holder...
That being said, an AS1674 compliant VRD will give you full voltage within 300ms of arc strike. I'd suggest you either have incorrect electrode selection, or a slow non compliant VRD. Or perhaps all the pipeline, mining and field service structural guys who need to use a VRD machine for work are also having the same problem getting a rod to strike?
Similar Threads
-
MIG welders - which one to buy
By MORRIMATE in forum WELDINGReplies: 14Last Post: 30th Sep 2016, 07:08 PM -
Any can welders?
By AxelVK in forum WELDINGReplies: 5Last Post: 22nd Feb 2013, 07:55 PM -
Old vs New Arc Welders
By newbyangler in forum WELDINGReplies: 26Last Post: 12th Mar 2011, 04:22 PM -
10 Amp Welders
By Sawmaster in forum WELDINGReplies: 21Last Post: 5th Apr 2010, 04:34 PM -
Welders
By XXXX in forum WELDINGReplies: 12Last Post: 11th Dec 2007, 07:03 AM