Page 17 of 17 FirstFirst ... 7121314151617
Results 241 to 249 of 249
  1. #241
    Join Date
    Mar 2009
    Location
    Melbourne
    Age
    47
    Posts
    551

    Default

    Just a quick follow up on this, I got a call last week to advise that my order had arrived and found time on Monday to swing by and pick it up.

    The AXA tool holders are pretty nice with the toolpost contact surfaces all nicely ground and a perfect fit. The clamp screws are high cheese alloy so I'll be replacing them but the holders themselves seem fairly hard. For $15.00 a pop I'm very happy with them.

    M & G Tooling 01.jpg

    The collet chucks are both quite nicely finished with ~0.01mm runout measured at the taper when in the lathe spindle or a collet in the mill so happy with them. The collets, while functional enough are a bit of a mixed bag finish wise. One is very nicely finished while the rest have a lot of sharp edges and a couple still had daggs from where the slits were cut. I checked the 16mm collet in the lathe and measured ~0.04mm runout on a slot drill shank, seems a bit ordinary to me but probably within my expectations given the price.

    M & G Tooling 02.jpg M & G Tooling 03.jpg

    Unfortunately the Mitee Bites are only available for 16mm slots but there was no problem returning them so all good.
    Cheers,
    Greg.

  2. #242
    Join Date
    Aug 2008
    Location
    Tennant Creek, Aust
    Age
    55
    Posts
    331

    Default

    Quote Originally Posted by kwijibo99 View Post
    Just a quick follow up on this, I got a call last week to advise that my order had arrived and found time on Monday to swing by and pick it up.

    The AXA tool holders are pretty nice with the toolpost contact surfaces all nicely ground and a perfect fit. The clamp screws are high cheese alloy so I'll be replacing them but the holders themselves seem fairly hard. For $15.00 a pop I'm very happy with them.

    M & G Tooling 01.jpg

    The collet chucks are both quite nicely finished with ~0.01mm runout measured at the taper when in the lathe spindle or a collet in the mill so happy with them. The collets, while functional enough are a bit of a mixed bag finish wise. One is very nicely finished while the rest have a lot of sharp edges and a couple still had daggs from where the slits were cut. I checked the 16mm collet in the lathe and measured ~0.04mm runout on a slot drill shank, seems a bit ordinary to me but probably within my expectations given the price.

    M & G Tooling 02.jpg M & G Tooling 03.jpg

    Unfortunately the Mitee Bites are only available for 16mm slots but there was no problem returning them so all good.
    Cheers,
    Greg.
    Greg do you have an AXA tool post from a different maker/ supplier?
    I am wondering as I bought mine from CDCO a few years ago, and want some more tool holders.
    Proud Hercus 260 owner.

    Ratty 05/2004 -05/07/2010 COOPER 01/08/1998-31/01/2012

  3. #243
    Join Date
    Mar 2009
    Location
    Melbourne
    Age
    47
    Posts
    551

    Default

    My tool post is a DTM wedge type out of the US.
    I would think AXA dovetail dimensions are standardised but who knows.
    Cheers,
    Greg.

  4. #244
    Join Date
    Mar 2008
    Location
    Brisbane
    Posts
    28

    Default

    I need some carbide burrs of reasonable quality, where do you buy yours

    Ken

  5. #245
    Join Date
    Aug 2008
    Location
    near Rockhampton
    Posts
    5,352

    Default

    For many years I have been after a proper sized magnetic chuck for my surface grinder. I did purchase a second hand one and found out you never buy a second hand magnetic chuck unless you can test it in person. Someone had pulled it apart and the alnico magnets had lost a substantial bit of their power because of it. Otherwise the chuck was really nice. Unfortunately getting the magnets rezapped means a trip to Melbourne. Freight is not cheap.

    I found Magpro2015 on ebay and asked about a 6X18 mag chuck. He said he could import one on his next order. Gave me a solid price and freight. It was $350 delivered. I said go ahead with the import and several months later he contacted me and said it had arrived and I bought it through his ebay shop. It was delivered by TNT and I have got it today. It is really nice, putting a micrometer to measure parallelism and the outside measures all under 0.01mm difference. The finish is superb. It is a fine pole chuck but things stick very well to it.

    Quite happy.

    https://www.ebay.com.au/sch/m.html?_..._skc=100&rt=nc
    Light red, the colour of choice for the discerning man.

  6. #246
    Join Date
    Apr 2013
    Location
    Toowoomba Qld
    Posts
    278

    Default

    Sorry if this is the wrong place to post this but couldn't think where else it might go
    Ebay is having a 18% tonight so was thinking I'll go shopping and tried to go to the MagPro2015 store to see if they had anything I wanted
    coming up as "No longer a registered user"
    https://www.ebay.com.au/usr/magpro2015
    Anyone know what the go is ? Their website still works but that doesn't mean much these days

  7. #247
    Join Date
    Jul 2016
    Location
    Melbourne
    Age
    29
    Posts
    280

    Default

    He is still very much in business but has taken his ebay store down for some reason. I bought some stuff off him last week. If you pm me ill give you his email.

  8. #248
    Join Date
    Jun 2005
    Location
    Nth Qld
    Posts
    90

    Default

    I have been talking to Felix from Magpro and he had issues with Ebay, so he is currently building a new website and you will be able to buy direct from it. It was supposed to be operational last week but he is still having issues.
    Rgds,
    Crocy.

  9. #249
    Join Date
    Aug 2015
    Location
    Melbourne, Australia
    Posts
    275

    Default

    Got a got number or email for magpro?

    edit: found the web site at last: M&G Productions Australia Pty Ltd

Page 17 of 17 FirstFirst ... 7121314151617

Similar Threads

  1. CTC Tooling
    By krisfarm in forum METALWORK GENERAL
    Replies: 9
    Last Post: 27th Mar 2010, 10:53 PM
  2. Lathe Tooling
    By glock40sw in forum METALWORK GENERAL
    Replies: 10
    Last Post: 13th Aug 2007, 08:39 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •