Search:
Type: Posts; User: steck
Search: Search took 0.00 seconds.
-
10th Feb 2017, 11:59 PM
Thread: Broken Cast Iron. I need help.
by steck- Replies
- 7
- Views
- 3,966
I just took my broken cast iron over to ...
I just took my broken cast iron over to kwijibo99 who did an excellent job saving my cast iron with a TIG welder.
Many many thank yous! -
3rd Feb 2017, 09:46 AM
Thread: Broken Cast Iron. I need help.
by steck- Replies
- 7
- Views
- 3,966
Hi Greg, I am happy to come up to...
Hi Greg,
I am happy to come up to Fawkner to get this fixed.
I will send you a PM.
Thanks,
Steve -
2nd Feb 2017, 04:35 PM
Thread: Broken Cast Iron. I need help.
by steck- Replies
- 7
- Views
- 3,966
Broken Cast Iron. I need help.
Hi,
HELP!
I'm working on restoring a very old cast iron sewing table for my wife. Everything was going great until I dropped the last piece and it snapped in 3 places! :doh:
I am told... -
16th Aug 2015, 07:22 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
The photos are great, thanks heaps! I have 3...
The photos are great, thanks heaps! I have 3 washers left in my cleaning tub and I am not sure where the 3rd one goes? I think it was either with the fly wheel or the gear on the other end of the...
-
29th Jul 2015, 10:03 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
Another problem solved! I opted for the slow...
Another problem solved! I opted for the slow cautious approach first and put it into the electrolysis bath for a day. (plus, I dont have an oxy torch!)
It is now moving 360 degrees but not yet... -
27th Jul 2015, 11:50 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
Aah! It begins to make sense! I can't loosen my...
Aah! It begins to make sense! I can't loosen my "pawl" (new word to add to the vocabulary!) That's the bit that's seized.
I may have to cut the rivet to remove it and then replace it. Any advice... -
27th Jul 2015, 10:32 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
Hi all, progress on this drill has been slow but...
Hi all,
progress on this drill has been slow but it's coming along. I have a question about the arm that moves the top wheel to lower the drill. Mine is seized. I assume that the toggle flips over... -
18th Jun 2015, 05:38 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
Bingo!! I sent off a few emails and Steel...
Bingo!!
I sent off a few emails and Steel Solutions replied in under 10 minutes. I drove round there and they cut to size and charged me $3. -
16th Jun 2015, 03:45 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
I have fired of an email to the Handy Steel...
I have fired of an email to the Handy Steel people. We'll see how that goes?
Thanks Vann for the offer. If I cant source it locally, I may take you up on it!
Bob, My drill is very very... -
15th Jun 2015, 07:03 PM
Thread: 19mm steel rod - Where to get some
by steck- Replies
- 24
- Views
- 9,574
19mm steel rod - Where to get some
Hi,
I am restoring a Buffalo Forge Post drill. (see Picture!)350046
The axle on which the Fly wheel and cog spin is rather battered and a bit corroded. It is 19mm diameter X 185mm. I presume... -
26th Feb 2008, 08:07 PM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
I love these woodwork forums because there are so...
I love these woodwork forums because there are so many good ideas out there.
I think I may just bit the bullet and buy the commercial drawers.
I can get this one 1700 long for $550.
I'd rather... -
17th Feb 2008, 08:37 AM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
This is the type of drawer slide I have seen in...
This is the type of drawer slide I have seen in the commercially available drawers. It is a section of rolled steel, formed to make a channel which sits on the roller bearings. If I can find out...
-
13th Feb 2008, 01:28 PM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
Yonnee, I stopped my Patrol drawers from rolling...
Yonnee,
I stopped my Patrol drawers from rolling out by putting a screw through the drawer in line with the top bearing. It has to be screwed in after the drawer is fitted and unscrewed if you... -
13th Feb 2008, 01:25 PM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
Thanks again for all the ideas and suggestions....
Thanks again for all the ideas and suggestions.
This is the camper trailer that I want to put the drawer in.
On our last trip to Birdsville, we used plastic tubs to put all the food and supplies... -
11th Feb 2008, 08:19 PM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
Thanks for the ideas so far. I can just buy a...
Thanks for the ideas so far.
I can just buy a ready made drawer from Tool Box for close to $1000!
But I am hoping to come out of it cheaper than that if I make my own.
Engineering wise it looks a... -
10th Feb 2008, 02:58 PM
Thread: Drawer slides advice needed.
by steck- Replies
- 22
- Views
- 19,497
Drawer slides advice needed.
Hi,
I want to make a sliding drawer for my camper trailer.
It will be 1700mm long X 500 wide X 30 high. I need 100% extension on the drawer, in fact, over extension would be a ideal.
Does anyone...