Search:

Type: Posts; User: romerod

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,604

    Hi has this part found a home yet? Cheers

    Hi has this part found a home yet?

    Cheers
  2. Replies
    2
    Views
    3,302

    Waldown 3M vs 8SN

    Hi All,

    I have a Waldown 8SN in good condition. I purchased it some years back from a bloke in Gippsland and unfortunately it has rusted up a bit as it was sitting exposed in the corner of his...
  3. Transtig 275 operating manual

    Better late than never. Hope this helps

    Cheers
  4. Replies
    80
    Views
    23,668

    waldown 8SN table rack

    Hi all
    High jacking the thread a bit I was wondering if anyone has experience with the Waldown 8sn table lift mechanism. When I purchased my unit the table lift was not operational. The rack rod...
  5. I have a copy of this manual around somewhere if...

    I have a copy of this manual around somewhere if you still want it for other information.

    Cheers
  6. Replies
    41
    Views
    38,186

    Little too late for me :-(

    Hi Sibrand,

    I was just searching the forums and came across my old thread on the Transtig 150. Seems like such a simple fix, I wish I still had it now as it was a well sized machine for what I...
  7. Replies
    41
    Views
    38,186

    Thanks for the help. She's sold

    :(( Hi guys thanks for all of the replies and help. I had no luck with all of my fault finding so I bit the bullet and sold it. Hopefully the next guy will have more luck than I did.

    thanks again...
  8. Replies
    41
    Views
    38,186

    Still no big spark

    :?:?
    Hi guys, been a bit busy with work and haven't been playing with the old Tig for the moment. Thanks to the replies so far. On the plus side I managed to repair my Fluke! It has a sneaky fusible...
  9. Replies
    41
    Views
    38,186

    Further update maybe its all over

    :cry4: I changed out the melted looking wire from the SCR to the change over panel on the front, got a new Dinse plug for BOC as well, point to note is that BOC supplied plugs are shorter than the...
  10. Replies
    41
    Views
    38,186

    Thanks for the heads up on that. I actually...

    Thanks for the heads up on that. I actually noticed that one of the plugs looks like it has arced and even melted the insulation a bit. Might see if I can get a new cable for it maybe?
  11. Replies
    41
    Views
    38,186

    Light bulb!

    Thanks for the reply. That makes so much sense! Just need to know how to test and check transformers. Any clues?

    there may be hope for the old girl yet.

    will keep you posted.

    cheers
  12. Replies
    41
    Views
    38,186

    Help? The update

    So all, thanks for all the replies and posting of manuals.

    i finally got hold of an air cooled tig torch and hooked up the Transtig 150. What if found was that the per and post flow timers and gas...
  13. Replies
    41
    Views
    38,186

    Thanks

    Thanks!! Need to get a hold of a Tig torch that fits to try it out.

    Will let you know
  14. Replies
    41
    Views
    38,186

    Thanks!

    Thanks!

    PM replied to, will see what the manual says.

    Cheers
  15. Replies
    41
    Views
    38,186

    Help my Transtig 150 is not working

    Hi I am having a horror run with Transtig welders at the moment. I recently purchased a EMF 250 Transtig which is in great condition but its too big for me and won't fit in my workshop. Apparently...
  16. Replies
    5
    Views
    6,664

    EMF Transtig 250

    Hi there,

    I have PM'd you my address.

    Cheers
  17. Replies
    5
    Views
    6,664

    Can I have a copy?

    Hi mate

    Any chance I could get a copy of that manual?


    I have one of these old machines as well and want to learn a bit more about it.


    cheers
Results 1 to 17 of 17