Search:

Type: Posts; User: Johnny Rocker

Search: Search took 0.00 seconds.

  1. Hercus change gears for sale or swap some for good 9" compound slide cash PerthWA

    I have the following Hercus change gears for sale, most of them look like they have done little or no work.
    All prices + postage
    80T Idler $40
    80T $39
    60T $38
    57T $37...
  2. Replies
    1
    Views
    4,428

    B.S.W. hand taps, 5/32, 3/16 Brand new

    range of new Sutton and P& N hand taps still in packaging 5/32 & 3/16 Tapper, Inter & Bottom, although not quite even amounts, $5 each + postage at cost.
    Lots of S/H taps, all different threads,...
  3. Replies
    2
    Views
    3,513

    Gotcha! Ta

    Gotcha! Ta
  4. Replies
    2
    Views
    3,513

    Buy/sell /swap for Hercus?

    Is there a dedicated forum for buying, selling or swapping Hercus bits?
    Or is it allowed here?
  5. Replies
    4
    Views
    3,072

    Just got my first Hercus!

    I recently bought a mates Hercus 9 model B. serial no 10270, ex tech school I believe.
    It came with a set of change gears, and the seller also gave me a box of assorted stuff the school gave hime...
  6. Yep, I have done that, much better than the...

    Yep, I have done that, much better than the original.
  7. Hafco AL50G 9 x 19 lathe carbide tool advice wanted

    hello, I have a Chinese made Hafco AL50G lathe, very much the same as many marketed under different brands.
    I am not a machinist, my passion is restoring classic and vintage motorcycles. So I do not...
  8. Replies
    7
    Views
    2,586

    Hi Bob, Thanks, but I dont have 3 phase, and,...

    Hi Bob,
    Thanks, but I dont have 3 phase, and, excuse my beginers ignorance, what is VFD short for?
  9. Replies
    7
    Views
    2,586

    Thanks Andrew, I think that may be a little over...

    Thanks Andrew,
    I think that may be a little over the top for what I want, I was just thinking of a 500w motor instead of the 350w standard one. The Seig SX2 mill is essentially the same but with...
  10. Replies
    7
    Views
    2,586

    Hafco HM10 mill drill

    I have had the HM10 for a few years, but found the 350W motor not quite powerful enough to do what i need, and it will "stall" sometimes.
    I recently acquired a herless SM1 Vertical mill, in good...
  11. Replies
    11
    Views
    5,541

    377494The offending damaged item

    377494The offending damaged item
  12. Replies
    1
    Views
    3,158

    still looking? I have one...

    still looking? I have one...
  13. Replies
    10
    Views
    2,453

    No problem, Kryn has first crack, but i will...

    No problem, Kryn has first crack, but i will reserve 1 of each left
  14. Replies
    10
    Views
    2,453

    For clarity, there is 7 x 5/32 inter = 3 x bottom...

    For clarity, there is 7 x 5/32 inter = 3 x bottom
    8 x 3/16 taper, 4 x inter 8 x bottom
    5 x 1/4 taper
    1 x 5/16 taper 1 x bottom.
  15. Replies
    10
    Views
    2,453

    377370

    377370
  16. Replies
    10
    Views
    2,453

    its only 460 x 480, 134k.. will make smaller

    its only 460 x 480, 134k.. will make smaller
  17. Thread: New guy

    by Johnny Rocker
    Replies
    16
    Views
    4,368

    I could, but you probably would want 2 vincents...

    I could, but you probably would want 2 vincents and 2 nortons...
  18. Replies
    10
    Views
    2,453

    For clarity, I have more than 1 of most of...

    For clarity, I have more than 1 of most of them...//metalworkforums.com/image/jpeg;base64,/9j/4Q/...
  19. Replies
    10
    Views
    2,453

    Johnny Rocker I have a selection...

    Johnny Rocker
    I have a selection of brand new BSW P +N and Sutton hand taps still in packaging in the following sizes:
    5/32 High Speed steel Inter P +N
    5/32 high Speed Steel Bottom...
  20. Replies
    10
    Views
    2,453

    BSW hand taps

    I have a selection of brand new BSW P +N and Sutton hand taps still in packaging in the following sizes:
    5/32 High Speed steel Inter P +N
    5/32 high Speed Steel Bottom Sutton
    3/16 Sutton Tungsten...
  21. Thread: New guy

    by Johnny Rocker
    Replies
    16
    Views
    4,368

    Well, I did suggest to SWMBO that she could park...

    Well, I did suggest to SWMBO that she could park her can on the street, I could then park mine in the drive and hey presto! problem solvered. She did quite see it that way and declined my problem...
  22. Replies
    11
    Views
    5,541

    377255This is the only other pic I have, prior to...

    377255This is the only other pic I have, prior to the shattering of the casting. The offending item is under the cylindrical weight to the right of the pic. I will take some better ones next time im...
  23. Thread: New guy

    by Johnny Rocker
    Replies
    16
    Views
    4,368

    377254This is my problem

    377254This is my problem
  24. Thread: New guy

    by Johnny Rocker
    Replies
    16
    Views
    4,368

    Thanks for your views, I think the best way to go...

    Thanks for your views, I think the best way to go would be to keep the lathe and turn the big mill, drill press and small mill drill into a decent mid size mill drill bench mounted?
    One of the...
  25. Thread: New guy

    by Johnny Rocker
    Replies
    16
    Views
    4,368

    New guy

    Hi,
    i have just joined, and to be honest, down have a huge amount of experience with fitting Turning. My main passion is restoring classic bikes. I have a Hafco AL50G lathe,
    a Hafco HM10 small...
  26. Replies
    11
    Views
    5,541

    if anyone around Perth is interested let me know...

    if anyone around Perth is interested let me know 0411080999
  27. Replies
    11
    Views
    5,541

    I dont need one, its just I hate to see good...

    I dont need one, its just I hate to see good things wasted377251
  28. Replies
    11
    Views
    5,541

    Hercus power hacksaw

    Hi, I have access to a Hercus power hacksaw, good condition except the large casting at the top is shattered. Is it worth saving, and if so, anyone know of any parts source?
    Any info or views...
Results 1 to 28 of 28