Search:
Type: Posts; User: tohot
Search: Search took 0.00 seconds; generated 50 minute(s) ago.
-
20th Sep 2018, 10:43 AM
Thread: Oil less air compressors.
by tohot- Replies
- 16
- Views
- 3,870
So, no one has one or is prepared to offer an...
So, no one has one or is prepared to offer an opinion? I thought you guys would have been all over this one... Oh well plenty of other forums around. I have noticed this forum seems to be going...
-
19th Sep 2018, 10:20 PM
Thread: Oil less air compressors.
by tohot- Replies
- 16
- Views
- 3,870
Oil less air compressors.
I'm looking at replacing my compressor which is around 2&5 years old but just too small. I want something of at least 200 LPM. Any info on the oil less type welcome.
-
19th Sep 2018, 06:37 PM
Thread: Name of degree scale on compound slide
by tohot- Replies
- 16
- Views
- 4,912
I assume your lathe has an angle scale held in by...
I assume your lathe has an angle scale held in by bang rivets. Why not make the marks permanent with a stamped or scratched on scale.
-
19th Sep 2018, 06:31 PM
Thread: Testing few Mics and callipers
by tohot- Replies
- 8
- Views
- 2,604
Micrometers come with test bars, why don't you...
Micrometers come with test bars, why don't you use them?
-
18th Sep 2018, 05:45 PM
Thread: Couple of new chucks for trial.
by tohot- Replies
- 0
- Views
- 1,957
Couple of new chucks for trial.
Today I bought a couple of new chucks: 1-13 keyed Vertex ball bearing chuck and a 3-16 keyless. At the moment the keyless is on the lathe and ball bearing one on the Pedestal. May swap them...
-
18th Sep 2018, 05:29 PM
Thread: Name of degree scale on compound slide
by tohot- Replies
- 16
- Views
- 4,912
Don't know there is a name for it, I just call it...
Don't know there is a name for it, I just call it an angle indicator,,,
-
17th Sep 2018, 10:46 PM
Thread: Belt Grinder
by tohot- Replies
- 25
- Views
- 13,406
As long as it's not a work wheel, Acetal or...
As long as it's not a work wheel, Acetal or aluminium would do the job. Acetal will get too hot and melt and aluminium has no give, rubber wheels are really the only alternative for a work wheel.
-
16th Sep 2018, 06:02 PM
Thread: Belt tensioner fix.
by tohot- Replies
- 0
- Views
- 982
Belt tensioner fix.
I changed the belt tensioning device on my lathe this afternoon.
Originally it had an idler on an adjustable backing, once tension was applied an allen key was used to tighten the locking bolt. ... -
14th Sep 2018, 10:39 AM
Thread: Cordless power tools ( from 2018 )
by tohot- Replies
- 30
- Views
- 5,498
I should ad my Bosch IXO. These cop a bit of...
I should ad my Bosch IXO. These cop a bit of criticism for not having adjustable torque. Bosch make various attachments for the IXO, ever a pepper grinder thingy, I don't have that but I do have...
-
13th Sep 2018, 11:27 PM
Thread: Cordless power tools ( from 2018 )
by tohot- Replies
- 30
- Views
- 5,498
I should ad, the M18 angle grinder is superb to...
I should ad, the M18 angle grinder is superb to use. My three corded angle grinders were pretty much retired when I bought the Xchange, now I have an M18 as well, they may well find their way on to...
-
13th Sep 2018, 09:17 PM
Thread: Cordless power tools ( from 2018 )
by tohot- Replies
- 30
- Views
- 5,498
Cordless power tools ( from 2018 )
A little while back I bought an Xchange cordless angle grinder for $49, cheap as chips! I already have a circular saw, LED, Drill and impact driver in the Xchange brand, all brushed bar the drill, ...
-
10th Sep 2018, 06:44 PM
Thread: Looking For Tooling Storage Ideas.
by tohot- Replies
- 21
- Views
- 7,159
Some pretty good ideas here, this is how I store...
Some pretty good ideas here, this is how I store my lathe bits and pieces: large drills at the rear along with ball turner, height set and knurler; tool holders, collet chuck, drill chuck, live...
-
8th Sep 2018, 05:05 PM
- Replies
- 16
- Views
- 8,907
Take it apart, easy job. Even if you leave the...
Take it apart, easy job. Even if you leave the headstock on it's still a lot lighter and easier to manage.
-
4th Sep 2018, 04:08 PM
Thread: keyed drill chucks
by tohot- Replies
- 3
- Views
- 1,449
keyed drill chucks
Anyone have one of these drill chucks: https://generaltools.com.au/product/vertex-1-16mm-keyed-drill-chuck-j6-mount/ or https://www.machineryhouse.com.au/C290
Any good? -
4th Sep 2018, 04:06 PM
Thread: 3/16 W left hand thread
by tohot- Replies
- 7
- Views
- 3,755
They should be available at any bolt/nut store.
They should be available at any bolt/nut store.
-
2nd Sep 2018, 01:05 PM
Thread: OT Non-hardening tube of silicon
by tohot- Replies
- 8
- Views
- 2,238
Generally the silicon in the nozzle goes off and...
Generally the silicon in the nozzle goes off and the remaining silicon gradually goes off over time. I simply extend the nozzle using a piece of plastic tube, pump the silicon into it and cap. ...
-
31st Aug 2018, 09:30 PM
Thread: zinc plated metric bolts
by tohot- Replies
- 6
- Views
- 2,727
You'll have to go to a bolt and nut supplier. ...
You'll have to go to a bolt and nut supplier. Hardwares only supply gal metric and zinc imperial form some reason now. Bunning's do have packs of zinc bolts and nuts but you'll pay through the...
-
30th Aug 2018, 11:38 AM
Thread: what is this thing please
by tohot- Replies
- 4
- Views
- 2,733
I'd go along with that, some Chinese sellers seem...
I'd go along with that, some Chinese sellers seem to specialise in bad descriptors, yet others use every tag they can think of. Others will advertise something but not give critical measurements a...