Search:

something like this?

369661

I pulled one of the old brunner's today. They don't appear to be the ones I remember. The ones I remember had tiny can opener type holes, this one has actual holes.
I put a 1/16 bit in the hole...

ok that was too easy and I discovered a magnet sticks to the pipe so if its stainless steel its ferritic stainless steel.


https://youtu.be/z9_-yrqkV3I

that's true I didn't think of that as a vise

how do i drill holes in a pipe without a starting bush to drill the holes in said pipe to use as a bush?

not trying to be funny


ah ok

What is a bush?

ah it was flat, the curve might not do as well how do i make a drill jig? it will guide the bit??

above what?

so the drill bit is going to run even though it's on a drill press?

If that's the case yesterday I drilled some tile with a hand drill that kept running, so i put 2 strips of masking tape over the...

How do I properly line up X and Y before bolting them down so that they are completely straight?

369137

A. something flat attachable to the pipe to stop it from rolling out of line while moving...

Their not burners yet. It was a 5 foot piece from a conveyer system on a palletizer machine. The bad ones get replaced every year. It could have been on there for 9 years.

I just think it's...

That's true I know i can rig it to work.
I bought it on craigslist so I thought it was broken or could be adjusted.
The spindle goes as far as it can and hits the end thats whats stopping it. I...

I'm at work but I did make a video this morning. It's not the best but you can see its as far left as it goes when starting. It goes so much to the right it goes off the screen.
...

I'm on my phone and clicked full site to add a picture to my post, but now can't seem to get back to the mobile version.

I searched Mobile version on the main forum search bar but didn't find it....

It's not an ad on. The position of where it's at on the screw it rides on needs to be adjusted

//metalworkforums.com/showthread.php?t=200928&p=1925341#post1925341

Related

Actually what part holds the vice? The mill?The one I just got off of Craigslist is off-center.


A's center is too far over to the right.
Shouldn't it be where C is?


How can I fix this?...

There not really holes more like can opener punctures. It's hard to say. The page that talked about 1/16" is on the PC in the bedroom and my wife is sleeping in there so I won't be able to link back...

The only speed settings close to that are 2180 RPM and 3070 RPM which one should I choose?

I bought it before I read your post. checked it for power.

from another site so I suppose that's the size bit I'll be looking for

Hi, not complaining or anything but why are we allowed to post 1 or 2 posts unmoderated and then all of a sudden we have to be approved by a moderator?
I edited mine a couple times and now my posts...

rigidity and quill movement??<br>
<br>
Well i hope its good, i bought it and only tested the power and 5 speeds from an outlet in the back of a Publix shopping center.<br>
Incase anyone ever needs...

rigidity and quill movement??

Well i hope its good, i bought it and only tested the power and 5 speeds from an outlet in the back of a Publix shopping center.
Incase anyone ever needs power on...

https://orlando.craigslist.org/tls/d/central-machinery-drill-press/6242734263.html


hmmm is this brand any good

NAME BRAND- CENTRAL MACHINERY
SPEED- 5 SPEED 760-3070 RPM
TABLE TILT- 45"...

hi ya'll

I'm finishing a project I started 2 years ago and need advice on how to drill 48 holes through 1/8 inch stainless steel.
The holes need to go all the way thru the pipe so it's actually...