Search:

Type: Posts; User: WC57

Search: Search took 0.03 seconds.

  1. Thread: Azstar mill tools

    by WC57
    Replies
    4
    Views
    10,793

    Hi, just came across this post. Did you buy any?...

    Hi, just came across this post. Did you buy any? I used them a lot while with a previous employer & they were very good. Cheers WC57
  2. Replies
    2
    Views
    4,982

    Thanks RC, the outer edges are still fine so I...

    Thanks RC, the outer edges are still fine so I will do as you suggest & repair what is needed.
  3. Replies
    2
    Views
    4,982

    Hardfacing question

    Hi, I have a loader bucket that has been hard faced before using a waffle pattern, but I don't know what sort of welding wire was used. It needs doing again & I would like to ask if it is ok to weld...
  4. Replies
    24
    Views
    6,390

    Well...I returned the machine to the seller for a...

    Well...I returned the machine to the seller for a refund today & would like to thank everyone who offered help via this forum. Unfortunately I didn't have time to follow up on every lead as time was...
  5. Replies
    24
    Views
    6,390

    Very interesting, thanks Kryn. I will see how I...

    Very interesting, thanks Kryn. I will see how I go getting hold of them...not giving up just yet.

    Out of curiosity, what amps to you think this thing would draw? It came fitted with a 32amp 3...
  6. Replies
    24
    Views
    6,390

    That's something else I was wondering...should...

    That's something else I was wondering...should the pneumatic side of it work even if the ignitron tubes are faulty. No electrical diagrams are in the machine, Inductotherm are checking to see if they...
  7. Replies
    24
    Views
    6,390

    This welder is fitted with the Ignitron tubes...

    This welder is fitted with the Ignitron tubes that are mentioned in the article on heat control which Michael G attached in an earlier response.

    When the power is turned on, apart from a small...
  8. Replies
    24
    Views
    6,390

    I thought I had updated this post...must not have...

    I thought I had updated this post...must not have hit submit. Anyhow, the following is part of a the reply that I received from Inductotherm last week:

    I am sorry to say, but I am not sure we can...
  9. Replies
    24
    Views
    6,390

    Interesting articles Michael, very helpful if I...

    Interesting articles Michael, very helpful if I ever get this thing going.

    No joy with the sparky today, he needs a wiring diagram. We did establish that there is a closed circuit between the...
  10. Replies
    24
    Views
    6,390

    Thanks Michael, very helpful information. I think...

    Thanks Michael, very helpful information. I think you might be onto something with you comment regarding a contactor controlling welding current. Hopefully I will know more by the end of today....
  11. Replies
    24
    Views
    6,390

    Thanks Jekyll & Hyde, I traced the E Stop wires...

    Thanks Jekyll & Hyde, I traced the E Stop wires back as far as I can go...they disappear into the main transformer somewhere. I have admitted defeat & have a sparky coming tomorrow morning to check...
  12. Replies
    24
    Views
    6,390

    Hi, I just spoke with Inductotherm & they appear...

    Hi, I just spoke with Inductotherm & they appear genuinely interested in trying to help me out. Unfortunately one service guy is on his way back from overseas & the other is off sick today, but the...
  13. Replies
    24
    Views
    6,390

    Sure, I will try to attach a pic of the control...

    Sure, I will try to attach a pic of the control panel here.

    I did email Inductotherm on Tuesday but have not received a reply, I will ring them today.
  14. Replies
    24
    Views
    6,390

    Thanks for the reply Stuart. I played around with...

    Thanks for the reply Stuart. I played around with it a bit more today including adjusting the squeeze time knob down to zero...still no good. There is a red light that comes on inside the control box...
  15. Replies
    24
    Views
    6,390

    Dorman spot welder help needed.

    Hi, I have just acquired a used 30KVA Dorman spot welder & am having trouble getting it to work. It originally came from the ACT TAFE, fitting & machining section. The model no is 1/PS/201/C with...
Results 1 to 15 of 15