Needs Pictures: 0
Results 1 to 12 of 12
Thread: Router bits
-
13th Jan 2017, 10:52 AM #1Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 422
Router bits
Just wanting your thoughts here.
I want to trim some aluminium in my mini milling machine. Do you think TC tipped wood router bits are suitable for the job ?
-
13th Jan 2017, 11:43 AM #2Most Valued Member
- Join Date
- May 2011
- Location
- Murray Bridge S Aust.
- Age
- 71
- Posts
- 5,942
That won't be a problem at all, have done it myself. Have known blokes to use the same cutters on steel, at a bit lower speed than a router though.
KrynTo grow old is mandatory, growing up is optional.
-
13th Jan 2017, 06:25 PM #3Novice
- Join Date
- Jul 2008
- Location
- Sydney Australia
- Age
- 76
- Posts
- 22
Hi,
I think they would be a better choice than HSS router bits, due to the cutting edge angle being relatively more suitable for aluminium than the fairly acute edge on the HSS bits. Then of course you could get a router bit ground for metal.
Cheers
-
13th Jan 2017, 09:32 PM #4Member: Blue and white apron brigade
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 7,182
Yep no probs - put some meths in a spray bottle and use that as a lube/coolant. Works a treat and no mess to clean up. Go easy though you can intoxicate yourself with the vapour if you are not careful.
Ally boat building BIL uses routers all the time - slightly overfill external corner welds and then routs the excess off using round over bits, comes up a treat.
-
13th Jan 2017, 09:54 PM #5Golden Member
- Join Date
- Nov 2010
- Location
- Gippsland Victoria
- Posts
- 733
Yes ...... have a go ............ With my RF30 mill I have cut matching dovetails in Aluminium using TC woodcutting router bits. I used kerosene to stop the Al sticking to the cutting edges.
I have even heard of people using TC router bits to cut steel.
Bill
-
13th Jan 2017, 10:02 PM #6Diamond Member
- Join Date
- Feb 2013
- Location
- Laidley, SE Qld
- Posts
- 1,038
I've seen those router bits used in a router on building sites to trim aluminium window frames. Lube was usually a stick of dry lube. Worked well.
-
14th Jan 2017, 01:26 AM #7
I agree with all the comments. I use diesel as a lube for alloy or WD40 on the circular saw. I've mentioned that I've used carbide router bits on steel several times, but has been pointed out there is no rake on the cutting edge so they tend to scrape rather than cut. A diamond or CBN wheel can change that.
Best Regards:
Baron J.
-
14th Jan 2017, 02:55 PM #8Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 422
Thanks everyone.
I used a half inch straight cutter and created a 20deg chamfer to the edge of 6mm aluminium.
I didn't bother with any lube but wow...cut like a champ and with a nice finish too.
My end mills cause a lot more vibration.
Good to know since the cost is good compared to the usual machining cutters and a nice variety of shapes and sizes.
-
15th Jan 2017, 10:44 AM #9Golden Member
- Join Date
- Jun 2007
- Location
- Vic
- Age
- 48
- Posts
- 544
I have done it with the wood router bit on steel also.
20160721_230016.jpg20160723_172506.jpg
-
20th Jan 2017, 11:55 AM #10Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 422
-
1st Mar 2017, 09:12 PM #11Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 422
I had another job to do where aluminium needed cutting.
This is an Aldi router table I bought a few years ago. I got it out to trim some timber maybe 12 months after I bought it and suddenly realized the platform surface was all wonky. It looked like whoever finished the work surface did it with a belt sander by hand. Dips and hollows and very uneven.
So I put it away again until yesterday.
I made up a jig to route it flat.
The jig has a couple of scrap pieces of black melamine for the router to slide on which I waxed to make it nice and slippery.
The lip around the under edge had to be machined first so that when it is place right side up it sits flat and level. I did that by clamping the router table onto four short pieces of 5mm steel rod placed at each corner under the black bits (in between the machined ridges), the routed the edge to make it even all around.
The table was then flipped and screwed down with right angle brackets then used the jig once again to machine the top ridges all even.
The router done a great job. Two passes removed about 1.5mm, which is what it took to get the surface even. All done at medium speed 12mm straight bit and no lube and advancing the router very slowly. When finished the cutter was still as sharp as.
After putting the router table back together I can declare it now work very nice.
I can see the headlines now, "Router fixes itself".
P1030506.jpgP1030507.jpg
-
1st Mar 2017, 11:14 PM #12
Hi Phaser,
I have one of those Aldi router tables as well ! The table on mine is nowhere near as bad as you describe yours. The fence I found to be absolute rubbish, I made a new one from a length of Beechwood. I keep promising myself that I will make a purpose designed table, one day, but I don't use it too often. I also found that my big 1/2" spindle router wont fit in the mountings, but the Aldi one does, though it seems slightly small in the recess.Best Regards:
Baron J.
Similar Threads
-
CNC Router
By Sterob in forum METALWORK GENERALReplies: 11Last Post: 19th May 2014, 09:34 AM -
router bits in lathe to mill aluminium - youtube video
By steamingbill in forum METALWORK GENERALReplies: 3Last Post: 29th Oct 2013, 06:55 PM -
CNC Router
By BigStick in forum METALWORK GENERALReplies: 5Last Post: 7th Aug 2011, 05:57 PM -
How about a cnc router sub page
By simso in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 7Last Post: 22nd Jan 2008, 08:15 PM