Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
-
12th Aug 2015, 11:57 AM #1
Can The Spoke Section Diameter Of A Drill Press Spindle Be Reduced By 0.2mm
Hi
I needed to purchase a new Spindle for my Waldown Drill Press that I am restoring. I purchased a replacement Spindle from Brobo however it turns out that my Waldown was one of the first 8SN series ever made. The first 8SN series had a spindle with a 16.3mm diameter spoke section however later version came with a 16.5mm. Waldown/Brobo do not have any 16.3mm spindles.
So my question is how difficult would it be to remove 0.2mm from the spindle on a metal lathe? Without compromising the concentric nature of the spindle.
I assume the spindle would be hardened steel.
Now I can buy a 1044110 – Upper Sleeve $88.00+GST from Brobo that will fit the new 16.5 spindle. For simplicity should I just buy a new Upper Sleeve or is reducing the size of the spoke section by 0.2mm doable?
Here is a photo of what I mean.
IMG_4747.jpgIMG_4746.jpg
-
12th Aug 2015, 12:46 PM #2Most Valued Member
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 9,088
Is there still a center in the end of the shaft?
Anything is possible though you might need to grind it. Whats a new one cost?
Stuart
-
12th Aug 2015, 01:05 PM #3Most Valued Member
- Join Date
- Jun 2007
- Location
- sydney ( st marys )
- Age
- 64
- Posts
- 4,890
Are the other dimensions compatible .
Have they increased I'd of the spline.( Minor Diameter).
-
12th Aug 2015, 05:35 PM #4
Are you sure it will fit if the outside diameter is reduced? Have you checked the other dimensions, spline (spoke) depth and width etc?
I think you will need to have it done on a cylindrical grinder. Is the a tapered hole in each end of the shaft to mount it between centres?…..Live a Quiet Life & Work with your Hands
-
12th Aug 2015, 05:52 PM #5Most Valued Member
- Join Date
- Jun 2007
- Location
- sydney ( st marys )
- Age
- 64
- Posts
- 4,890
You wouldn't want a tapered hole at each end.
-
12th Aug 2015, 05:54 PM #6
Aren't the holes for centres countersunk? Trying to give a non-metal worker a layman's description.
…..Live a Quiet Life & Work with your Hands
-
12th Aug 2015, 06:10 PM #7Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 6,218
Depends on your financial situation and you have to be absolutely sure your current new spindle with spline will fit the old splined bush.
You may find the 16.5mm splines have a larger minor diameter then the old 16.3mm spline..
The risk is the price of a new spindle verses $88 for the new part....Gold, the colour of choice for the discerning person.
-
12th Aug 2015, 07:22 PM #8Banned
- Join Date
- Jul 2011
- Location
- Melbourne Australia
- Posts
- 1,376
Do you think its tough or hardened? I wouldn't attempt to turn it, for a factor of 0.1mm per side. I'd grind it, but I can do that in-house.
Splines normally locate on the O.D of the male. This will have a mass of clearance being a sliding spline, but it should be kept true.
Run a file over the end of one spline tooth, and see if it's even turnable.
Regards Phil.
-
12th Aug 2015, 10:51 PM #9
Yes
Yes
The spindle cost $300 a new upper sleeve would only cost $100 more. It sounds that it would be safer to simple buy a new upper sleeve. Since the spindle is hardened rock hard.
Thanks for everyones input. But I think it will be easier and safer to pay up for a new upper sleeve.
-
12th Aug 2015, 11:27 PM #10Banned
- Join Date
- Jul 2011
- Location
- Melbourne Australia
- Posts
- 1,376
Similar Threads
-
Waldown type H drill press info reqd. (spindle lubrication)
By johntopp in forum METALWORK GENERALReplies: 2Last Post: 18th Nov 2014, 03:56 PM -
Richarson drill press spindle
By chalmers888 in forum METALWORK GENERALReplies: 9Last Post: 24th Apr 2013, 10:16 PM