Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Page 1 of 2 12 LastLast
Results 1 to 15 of 20
  1. #1
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default parting tool geometry

    Ive been trying to part of some 35mm steel in my lathe, im running at about 150rpm and got the auto cross slider feed on 0.029mm/rev and it just isnt happening, stalled the lathe, tool dug in even snapped the blade off today. i did try to slow the feed rate down to no luck, which brings me to is the tool geometry right. whats the correct geometry for parting tools?

    thanks

  2. #2
    Join Date
    Aug 2011
    Location
    Melbourne
    Posts
    4,779

    Default

    I used to have all sorts of issues with parting off. Similar to you, snapping blades and ripping the workpiece out of the chuck being the biggest issues. Then, there was a time when Stuart (stustoys) and I were talking shed stuff and he mentioned about reducing the back rake so that the tool is not so inclined to be pulled in to the work. I now grind my part off tools with very little back rake and it's pretty much fixed all my issues. I use a few other precautions too though. With large stock requiring deep cuts, I often part off in two places right next to eachother to create better tool clearance. I also withdraw the tool frequently to clear swarf, err on more feed rate rather than less, especially with stainless and I always use a form of lubricant, use the least amount of tool overhang as possible to get the job done and do it as close as possible to the chuck.

    If you are using a part off blade that is thicker at top than the bottom, make sure you don't grind it upside down or it will not have the required clearance and it will grab. I don't use carbide part off blades, no need for my uses and they seem so expensive compared to a seemingly endless piece of HSS.

    I still get nervous when parting large parts because of what used to happen, things would often seem OK and doing well and then at the last minute BANG! Bits everywhere!

    Simon
    Girl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.

  3. #3
    Join Date
    May 2011
    Location
    Murray Bridge S Aust.
    Age
    71
    Posts
    5,942

    Default

    Any chance of pics to show what you mean, please Simon. Always interested in learning something new.

  4. #4
    Join Date
    Aug 2008
    Location
    near Rockhampton
    Posts
    6,216

    Default

    lubricant, lubricant and more lubricant is a major secret of successful parting off with HSS...
    Gold, the colour of choice for the discerning person.

  5. #5
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default

    Quote Originally Posted by simonl View Post
    I used to have all sorts of issues with parting off. Similar to you, snapping blades and ripping the workpiece out of the chuck being the biggest issues. Then, there was a time when Stuart (stustoys) and I were talking shed stuff and he mentioned about reducing the back rake so that the tool is not so inclined to be pulled in to the work. I now grind my part off tools with very little back rake and it's pretty much fixed all my issues. I use a few other precautions too though. With large stock requiring deep cuts, I often part off in two places right next to eachother to create better tool clearance. I also withdraw the tool frequently to clear swarf, err on more feed rate rather than less, especially with stainless and I always use a form of lubricant, use the least amount of tool overhang as possible to get the job done and do it as close as possible to the chuck.

    If you are using a part off blade that is thicker at top than the bottom, make sure you don't grind it upside down or it will not have the required clearance and it will grab. I don't use carbide part off blades, no need for my uses and they seem so expensive compared to a seemingly endless piece of HSS.

    I still get nervous when parting large parts because of what used to happen, things would often seem OK and doing well and then at the last minute BANG! Bits everywhere!

    Simon
    have you got a pic of the tool?

    i was using lots of cutting oil but still had no luck.

  6. #6
    Join Date
    Aug 2011
    Location
    Melbourne
    Posts
    4,779

    Default

    I'll duck out to the shed at take a pic of my blades. Bare in mind that there are many people far more experienced than me when it comes to (successful) parting off.

    Simon
    Girl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.

  7. #7
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default

    Quote Originally Posted by simonl View Post
    I'll duck out to the shed at take a pic of my blades. Bare in mind that there are many people far more experienced than me when it comes to (successful) parting off.

    Simon
    no worries mate, see what the others have to say.

  8. #8
    Join Date
    Sep 2008
    Location
    Riddells Creek, Vic.
    Posts
    831

    Default

    It could have more to do with the Lathe rather than the tool geometry, what type of machine are you using?

  9. #9
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default

    Quote Originally Posted by Techo1 View Post
    It could have more to do with the Lathe rather than the tool geometry, what type of machine are you using?
    its an old herless, basicly an al960b sold by hare and forbes

  10. #10
    Join Date
    Aug 2011
    Location
    Melbourne
    Posts
    4,779

    Default

    Here are my 3 blades I use. Looking at them they are a little tired and probably need a re-sharpen before next use but the geometry can be seen. The second pic is end on to show how the wedge shape provides clearence from the rest of the tool… assuming you don't do what I did and sharpen upside down so that the cutting is done at the narrowest (thinest part) and then siezes when fed in!

    I also used to blame the quality of the steel too. But you can see that one of the blades is made in India and the others are China. Not top quality stuff but it still works for me. Also, I rarely use auto feed. I like to feel the tool cutting and vary the feed rate until it feels nice. It should feel like your cutting butter, if it doesn't then there is something not right. I find that feeding not enough can be worse than too much especially with stainless steel, it needs a nice positive feed rate or the tool will just work harden the work and rub and go blunt.

    Simon 20150521_183957.jpg 20150521_184042.jpg

    Edit: I just read Techo's response. The other things that you may want to look at are spindle bearings, cross slide and compound backlash and gibb adjustment but my experience showed the vast majority of my issues were user related such as tool geometry, feed rates, lubrication and tool rigidity. Also, don't forget to wind in your compound all the way. I do this because my Chinese lathe has a less than perfect compound and winding it in all the way adds to rigidity.

    Cheers
    Girl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.

  11. #11
    Join Date
    Mar 2009
    Location
    Melbourne
    Age
    54
    Posts
    825

    Default

    I've had similar issues, I reckon everyone has fun and games when they first use a parting tool, it really fires the pucker reflex when the tool grabs and shatters with a bang.
    I generally have good results with the following:

    For steel or staino no top rake at all and keep the tool lubricated with oil, not the milky soluble stuff, proper cutting oil if you can get it, I use the Trefolex CDT in a spray can. Never let the tool rub on staino or it will work harden. For 35mm free cutting steel 150-200 rpm will be good to start but speed it up as the cut gets deeper, should be around 400 by the time you finish. Lower speeds for harder steel alloys and slower again for staino, a VFD is at its most useful when parting.

    For brass or bronze a bit of negative or no top rake, I don't use any lube and rpm can be a bit faster.

    For ally or plastic, grind a bit of positive top rake (2 o 3 degrees) no lube for plastic and a bit of kero, diesel or cutting oil for ally, again higher rpm is ok.

    In general, keep the front relief small to support the tip, I usually feed the tool straight into the grinding wheel and let the curvature create the front relief. Make sure tool is set 90 degrees to work and on centre or even a little below but never above. Keep tool extension from holder as small as possible, extend tool out as cut progresses if necessary. Again increase rpm as cut progresses, if speed is too low it will be more inclined to dig in.

    Cheers,
    Greg.

  12. #12
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default

    Thanks for the pics. Ill try have a go at that. Because i mainly use carbide im not really cluded up on what back rake ect ect is. Could somone help me out?

  13. #13
    Join Date
    Aug 2008
    Location
    near Rockhampton
    Posts
    6,216

    Default

    My other take on it is front clearance should be kept as small as possible, this is what will stop the tool from digging in and is sort of you depth of cut restrictor..

    A real learned person like Steamwhisperer may have the most parting secrets to give up...

    I gave up with HSS and went to carbide inserts...
    Gold, the colour of choice for the discerning person.

  14. #14
    Join Date
    Aug 2011
    Location
    Melbourne
    Posts
    4,779

    Default

    Quote Originally Posted by brendanh View Post
    Thanks for the pics. Ill try have a go at that. Because i mainly use carbide im not really cluded up on what back rake ect ect is. Could somone help me out?
    Have a look at these pics and then compare to my pics and it will give you an idea of rake angles and front relief. You can see that my tools have very little positive rake angle. Greg suggests zero or negative for brass or bronze but I rarely change my angles specific to material type, mainly cause I'm too lazy.

    rake.jpg

    Toolbit.gif This is for a general lathe cutting tool but the front relief is the same concept.

    Cheers,

    Simon
    Girl, I don't wanna know about your mild-mannered alter ego or anything like that." I mean, you tell me you're, uh, super-mega-ultra-lightning babe? That's all right with me. I'm good. I'm good.

  15. #15
    Join Date
    Jan 2015
    Location
    Sydney
    Posts
    211

    Default

    So thats the back rake..front releif i guess is the angle on the front of the tool

Page 1 of 2 12 LastLast

Similar Threads

  1. Replies: 19
    Last Post: 19th Mar 2014, 02:29 PM
  2. Your best parting tool
    By iron bark in forum METALWORK GENERAL
    Replies: 61
    Last Post: 20th Dec 2012, 07:40 PM
  3. Parting tool mounted on rear tool post advice needed
    By colbra in forum METALWORK GENERAL
    Replies: 17
    Last Post: 12th Feb 2012, 02:49 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •