Results 1 to 10 of 10
  1. #1
    Join Date
    Jan 2013
    Location
    Tasmaniac
    Posts
    9

    Default Can anyone identify/shed light on these 2 guns

    Was hoping someone out there might be able to identify these 2 unusual old pistols.
    This one is rough as guts, bits missing. The lever that goes over the flash pan (if that's the right name for it)still moves but the other bits are seized up. Length is about 450mm long, bore is about 17mm.
    DSCF4972.jpgDSCF4973.jpgDSCF4974.jpgDSCF4975.jpg

    This one is much smaller, about 230mm long. Trigger and hammer work. It has a tapered bore which at the widest diameter at the muzzle is 19mm. Looks like you could use anything for a projectile eg, a handful of small stones etc.
    DSCF4976.jpgDSCF4977.jpgDSCF4978.jpg
    Any comments or thoughts greatly appreciated.

  2. #2
    Join Date
    Sep 2011
    Location
    Ballarat
    Age
    65
    Posts
    3,103

    Default

    Try googling blunderbus pistol.

    Phil

  3. #3
    Join Date
    Jan 2013
    Location
    Tasmaniac
    Posts
    9

    Default

    Quote Originally Posted by Steamwhisperer View Post
    Try googling blunderbus pistol.

    Phil
    Yes Steamwhisperer, there sure is a vast array of them on "images for blunderbus pistols". Couldn't see one the same as mine.

  4. #4
    Join Date
    Dec 2007
    Location
    Adelaide
    Posts
    574

    Default

    The larger of the two is flintlock black powder pistol the brass but plate looks quite ornate and from this you could probably reason that it was possibly one of a pair made for wealthy clients/officers. The lever over the flash pan is called the frizzen or steel, a flint held in the jaws of the hammer would strike the frizzen producing a shower of sparks at the same time the action of the flint against the frizzen would snap it open exposing a small charge of black power in the pan, the powder would ignite with a flash igniting the main powder charge in the barrel through the touch hole which should be visible near the bottom of the pan. The term flash in the pan comes from this where the main charge fails to ignite.

    The smaller is a box lock percussion pistol sometimes called a pocket or coat pistol, also black powder the main charge is ignited by a percussion cap fitted over the nipple which protrudes from the rear of the barrel, much more reliable than the flintlock. The funnel end on the barrel may possibly indicate that solid ball or lead shot could be used.

    Both pistols load by pouring a measured powder charge into the barrel from the muzzle end and then finishing off with a suitable ball being rammed down on top of the powder charge.

    If you are unsure of the history of the guns make absolutly sure there is no old powder charge left in the barrel of either of them before doing anything.

    Even though the flintlock looks like a basket case I believe it looks very restorable, the pocket pistol looks in fair shape for its age and would not take a great deal of work to restore. If you do plan to restore seek advise from an expert as refinishing the patina can destroy any value the gun has.

    Flitlocks reigned in the 1700's and were gradually phased out from around 1820 when percussion caps were introduced,

  5. #5
    Join Date
    Oct 2011
    Location
    Norwood-ish, Adelaide
    Age
    59
    Posts
    6,541

    Default

    Possibly worth talking to a museum about who could restore or provide you with more information. Not sure what the situation in TAS is with respect to licensing & regulations of historic firearms but don't forget to check that out too.

    Michael

  6. #6
    Join Date
    Sep 2015
    Location
    Perth
    Posts
    62

    Default

    The 1st looks like a 1750's Heavy Dragoon pattern - many makers of these. It's missing its brass trigger guard. Are there any markings on the barrel or on the plate under the fore-end??

    Measure from the mouth of the barrel to where the flash pan is, then gently (standing to the side) insert a wooden dowel down the barrel. If there is more than about 1.5cm difference you probably have a ball and powder in there and its live. If less than 1.5cm but still short of the muzzle/pan measurement there is probably still powder in there and its live.

    It is possible to unload these using compressed air through the flash hole but only if you know what you are doing.

    As with all these things, I accept no responsibility etc etc.

  7. #7
    Join Date
    May 2011
    Location
    Murray Bridge S Aust.
    Age
    71
    Posts
    5,942

    Default

    If it has a ball or loaded with powder, get a self tapper welded onto the end of a bit of 6 or 8 mm bar longer than the barrel, welded with a T on the end. Screw this into the ball or patch to remove to make it safe, something similar can be bought. Saw this used a long time ago when I used to shoot rifle and pistol, unfortunately not Black Powder.
    Kryn

  8. #8
    Join Date
    Jan 2013
    Location
    Tasmaniac
    Posts
    9

    Default

    Thanks for the feedback. They are definitely not loaded.
    My mum bought them from a garage sale in Sydney years ago.
    Got a thread going on in the sculpture and woodcarving section of the woodwork forums some of you gun enthusiasts might be interested in? If so click here....http://www.woodworkforums.com/showthread.php?t=189595

  9. #9
    Join Date
    Dec 2007
    Location
    Western Australia
    Posts
    11

    Default

    I'll hazard a guess and say the top pistol is something from the borderlands in India/Afghanistan and the bottom may be a Belgian made pocket pistol for travellers. Not made for stones but an assortment of shot that would be 'discouraging' at short range.
    "Entia non sunt multiplicanda praeter necessitatem"

  10. #10
    Join Date
    Apr 2008
    Location
    NSW
    Posts
    537

    Default

    The bottom one could be a
    PERCUSSION BLUNDERBUSS PISTOL, Belgian, circa 1840.
    The volume of a pizza of thickness 'a' and radius 'z' is given by pi z z a.

Similar Threads

  1. Replies: 17
    Last Post: 29th Jan 2014, 10:31 PM
  2. How guns are made, one at a time
    By neksmerj in forum METALWORK GENERAL
    Replies: 0
    Last Post: 10th Sep 2013, 04:31 PM
  3. Spray Guns
    By Keith_W in forum METALWORK GENERAL
    Replies: 15
    Last Post: 14th Jan 2013, 09:31 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •