Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Hercus 260 Footprint
-
10th Oct 2018, 05:51 PM #1New Member
- Join Date
- Aug 2016
- Location
- Wollongong NSW
- Age
- 30
- Posts
- 1
Hercus 260 Footprint
Gday all,
After squeezing in my Colchester and a couple of mills, my small shed is just about at max capacity, however I’ve always wanted a 260 Atm.
Could a kind hercus owner please quickly chuck a tape over their 260 ATM on the factory steel cabinet and let me know how much space I’ll need to make to fit one in?
I’m after an overall length and depth of the lathe on the cabinet, height of the headstock and any extra distance it’ll need off the wall if the motor hangs off the back of the cabinet.
Any help would be much appreciated.
Cheers
James
-
10th Oct 2018, 07:24 PM #2Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,898
From 260 brochure:
-
10th Oct 2018, 07:55 PM #3Senior Member
- Join Date
- Nov 2008
- Location
- Sydney
- Posts
- 112
You will need an extra 140mm minimum clearance between a wall and the headstock cover in order to be able to open it.
Chas.
-
11th Oct 2018, 09:12 AM #4
-
11th Oct 2018, 02:39 PM #5Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,898
Hercus brochures for the 9 inch models don't seem to have overall dimensions.
I can measure my 9A, if you have specific queries.
-
12th Oct 2018, 10:20 AM #6
Basically I am after measurements,
Height, from top of lathe to bottom of tray, ( the 260 is 18")
Length, any part that overhangs the head stock end, otherwise I will use the measurements of the tray.
Width, from front of tray to anything that overhands at rear. ( the 260 is 24")
The plan is to get a Heavy Duty cover made that will attach to base of the tray.
I live in a very dusty climate, I found covers like this is the only way to stop the dust getting in.
Cheers,
Mark.
Ratty 05/2004 -05/07/2010 COOPER 01/08/1998-31/01/2012
-
12th Oct 2018, 11:59 PM #7Mechanical Butcher
- Join Date
- Oct 2004
- Location
- Southern Highlands NSW
- Posts
- 1,898
The tray I have is a simple rectangle with curved corners, I think it's a standard Hercus one but mounted to a non-Hercus table. NB: There are other types of tray, e.g. with angled corners that I think are bigger.
Mine has angled lips, dimensions at the extremes of these are 44.5" x 12".
All dimensions below are taken from the top edges of the angled tray lips, except for the height.
At the back, the motor is the rearmost part, and it overhangs the tray by 12" (24" total). Being an early version, there is no pivoting adjustment for the motor belt - later pivoted type may overhang more? My motor slides vertically to adjust the belt, so would not increase the overhang.
At the front, the cross slide handle is 4.5" in front of the tray. Hinged headstock cover, Norton gearbox, saddle wheel, etc also overhang but not as far as the cross slide handle.
At the left, the headstock gear cover doesn't overhang. It is flush with the left side of the tray.
Height is 27.75" from top of countershaft big pulley to the bottom of the tray. That is with the belt tensioning lever in its lowered position. Obviously, I have the common "upright" motor drive type.
Hope that helps.
-
15th Oct 2018, 08:42 PM #8
-
4th Nov 2018, 04:10 PM #9
Do you still need help Mark? I just landed 2 of them and will be in the shop tomorrow if you need factory original measurements. Let me know. They are late model 260s sitting on original stands.
Cheers
Similar Threads
-
Hercus 9" vs hercus 260 ????????
By bitza500 in forum THE HERCUS AREAReplies: 1Last Post: 26th Jun 2009, 10:50 PM -
Hercus parts on Ebay from Hercus
By bollie7 in forum THE HERCUS AREAReplies: 0Last Post: 8th Oct 2008, 02:59 PM